Cisco 8832 Administration Guide

Possible Explanation and ActionDescriptionMessage
Occurs if you attempt to install a version
of software on this phone that did not
support hardware changes on this phone.
Check the load ID that is assigned to the
phone (from Cisco Unified
Communications Manager, choose
Device > Phone). Reenter the load that
displays on the phone.
The application that was downloaded is not
compatible with the phone hardware.
Load Rejected HC
If the phone has a static IP address, verify
that the default router is configured.
If you are using DHCP, the DHCP server
has not provided a default router. Check
the DHCP server configuration.
DHCP or static configuration did not
specify a default router.
No Default Router
If the phone has a static IP address, verify
that the IPv4 DNS server is configured.
If you are using DHCP, the DHCP server
has not provided a IPv4 DNS server. Check
the DHCP server configuration.
A name was specified but DHCP or static
IP configuration did not specify a IPv4
DNS server address.
No IPv4 DNS Server
If the phone has a static IP address, verify
that the IPv6 DNS server is configured.
If you are using DHCP, the DHCP server
has not provided a IPv6 DNS server. Check
the DHCP server configuration.
A name was specified but DHCP or static
IP configuration did not specify a IPv6
DNS server address.
No IPv6 DNS Server
The trust list is not configured on the Cisco
Unified Communications Manager, which
does not support security by default.
The trust list is not configured.
For more information about trust lists, see
the documentation for your particular Cisco
Unified Communications Manager release.
The CTL file or the ITL file is not installed
on the phone.
No Trust List Installed
Update the certificate.FIPS requires that the RSA server
certificate is 2048 bits or greater.
Phone failed to register. Cert key size is not
FIPS compliant.
Configuration changes were likely made to
the phone in Cisco Unified
Communications Manager, and Apply
Config was pressed so that the changes take
effect.
The phone is restarting due to a request
from Cisco Unified Communications
Manager.
Restart requested by Cisco Unified
Communications Manager
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
128
Cisco IP Conference Phone Troubleshooting
Status Messages Fields

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g