Cisco 8832 Administration Guide

Value or RangeSpecification
IEEE PoE Class 3 via a PoE injector. The phone is
compatible with both IEEE 802.3af and 802.3at switch
blades and supports both Cisco Discovery Protocol
and Link Layer Discovery Protocol - Power over
Ethernet (LLDP-PoE).
Other options include a non-PoE Ethernet injector if
the connected LAN switches don't support PoE. For
WiFi deployment, a Cisco IP Conference Phone 8832
Power Adapter is needed.
Power
Secure bootSecurity features
USB-CCables
The Ethernet Specification assumes that the maximum
cable length between each conference phone and the
switch is 100 meters (330 feet).
Distance Requirements
For more information, see the Cisco IP Conference Phone 8832 Data Sheet: https://www.cisco.com/c/en/us/
products/collaboration-endpoints/unified-ip-phone-8800-series/datasheet-listing.html
Phone Power Requirements
The Cisco IP Conference Phone 8832 can use these power sources:
• Power over Ethernet (PoE) deployment with a Cisco IP Conference Phone 8832 PoE Injector
• Non-PoE Ethernet deployment with a Cisco IP Conference Phone 8832 Non-PoE Ethernet Injector
• Wi-Fi deployment with a Cisco IP Conference Phone 8832 Power Adapter
Table 3: Guidelines for Cisco IP Conference Phone Power
GuidelinesPower Type
If you are using either the Cisco IP Conference Phone 8832 PoE Injector
or Cisco IP Conference Phone 8832 Ethernet Injector, make sure that
the switch has a backup power supply to ensure uninterruptible operation
of the phone.
Ensure that the CatOS or IOS version that runs on your switch supports
your intended phone deployment. See the documentation for your switch
for operating system version information.
When you install a phone that is powered by PoE, connect the injector
to the LAN before you connect the USB-C cable to the phone. When
you remove a phone that uses PoE, disconnect the USB-C cable from
the phone before you remove the power from the adapter.
PoE power—Provided by either the
Cisco IP Conference Phone 8832
PoE Injector or Cisco IP
Conference Phone 8832 Ethernet
Injector through the USB-C cable
attached to the phone.
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
16
About the Cisco IP Conference Phone
Phone Power Requirements

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g