Cisco 8832 Administration Guide

You can configure the number of times a Wi-Fi phone sends an authentication request to the Wi-Fi server.
The default number of attempts is 2, but you can set this parameter from 1 to 3. If a phone fails the
authentication, then the user is prompted to sign in again.
You can apply WLAN Authentication Attempts to individual phones, to a pool of phones, or to all the Wi-Fi
phones in your network.
Procedure
Step 1 In Cisco Unified Communications Manager Administration, select Device > Phone and locate the phone.
Step 2 Navigate to the Product Specific Configuration area and set the WLAN Authentication Attempts field.
Step 3 Select Save.
Step 4 Select Apply Config.
Step 5 Restart the phone.
Enable WLAN Prompt Mode
Enable WLAN Profile 1 Prompt Mode if you want a user to sign into the Wi-Fi network when their phone
powers-up or resets.
Procedure
Step 1 In Cisco Unified Communications Manager Administration, select Device > Phone.
Step 2 Locate the phone that you need to set up.
Step 3 Navigate to the Product Specific Configuration area and set the WLAN Profile 1 Prompt Mode field to
Enable.
Step 4 Select Save.
Step 5 Select Apply Config.
Step 6 Restart the phone.
Set Up a Wi-Fi Profile using Cisco Unified Communications Manager
You can configure a Wi-Fi profile and then assign the profile to the phones that support Wi-Fi. The profile
contains the parameters required for phones to connect to the Cisco Unified Communications Manager with
Wi-Fi. When you create and use a Wi-Fi profile, you or your users do not need to configure the wireless
network for individual phones.
Wi-Fi profiles are supported on Cisco Unified Communications Manager Release 10.5(2) or later.
A Wi-Fi profile enables you to prevent or limit changes to the Wi-Fi configuration on the phone by the user.
We recommend that you use a secure profile with TFTP encryption enabled to protect keys and passwords
when you use a Wi-Fi profile.
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
46
Cisco IP Conference Phone Installation
Enable WLAN Prompt Mode

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g