Cisco 8832 Administration Guide

Related Topics
Cisco Unified Communications Manager Documentation, on page 12
Add a User from an External LDAP Directory
If you added a user to an LDAP Directory (a non-Cisco Unified Communications Server directory), you can
immediately synchronize the LDAP directory to the Cisco Unified Communications Manager on which you
are adding the user and the user phone.
If you do not synchronize the LDAP Directory to the Cisco Unified Communications Manager immediately,
the LDAP Directory Synchronization Schedule on the LDAP Directory window determines when the next
autosynchronization is scheduled. Synchronization must occur before you can associate a new user to a device.
Note
Procedure
Step 1 Sign into Cisco Unified Communications Manager Administration.
Step 2 Select System > LDAP > LDAP Directory.
Step 3 Use Find to locate your LDAP directory.
Step 4 Click on the LDAP directory name.
Step 5 Click Perform Full Sync Now.
Add a User Directly to Cisco Unified Communications Manager
If you are not using a Lightweight Directory Access Protocol (LDAP) directory, you can add a user directly
with Cisco Unified Communications Manager Administration by following these steps.
If LDAP is synchronized, you cannot add a user with Cisco Unified Communications Manager Administration.
Note
Procedure
Step 1 From Cisco Unified Communications Manager Administration, choose User Management > End User.
Step 2 Click Add New.
Step 3 In the User Information pane, enter the following:
• User ID: Enter the end user identification name. Cisco Unified Communications Manager does not permit
modifying the user ID after it is created. You may use the following special characters: =, +, <, >, #, ;,
\, , “”, and blank spaces. Example: johndoe
• Password and Confirm Password: Enter five or more alphanumeric or special characters for the end user
password. You may use the following special characters: =, +, <, >, #, ;, \, , “”, and blank spaces.
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
58
Cisco IP Conference Phone Installation
Add a User from an External LDAP Directory

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g