Cisco 8832 Administration Guide

CHAPTER 4
Phone Installation
• Verify the Network Setup, on page 25
• Enable Autoregistration for Phones, on page 26
• Daisy Chain Mode, on page 27
• Install the Conference Phone, on page 28
• Set Up the Phone from the Setup Menus, on page 36
• Enable Wireless LAN from the Phone, on page 42
• Verify the Phone Startup, on page 48
Verify the Network Setup
As they deploy a new IP telephony system, system administrators and network administrators must complete
several initial configuration tasks to prepare the network for IP telephony service. For information and a
checklist for setting up and configuring a Cisco IP telephony network, see the documentation for your particular
Cisco Unified Communications Manager release.
For the phone to operate successfully as an endpoint in your network, your network must meet specific
requirements. One requirement is the appropriate bandwidth. The phones require more bandwidth than the
recommended 32 kbps when they register to Cisco Unified Communications Manager. Consider this higher
bandwidth requirement when you configure your QoS bandwidth. For more information, refer to Cisco
Collaboration System 12.x Solution Reference Network Designs (SRND) or later ( https://www.cisco.com/c/
en/us/td/docs/voice_ip_comm/cucm/srnd/collab12/collab12.html ).
The phone displays the date and time from Cisco Unified Communications Manager. The time displayed on
the phone can differ from the Cisco Unified Communications Manager time by up to 10 seconds.
Note
Procedure
Step 1 Configure a VoIP Network to meet the following requirements:
• VoIP is configured on your routers and gateways.
• Cisco Unified Communications Manager is installed in your network and is configured to handle call
processing.
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
25

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g