Cisco 8832 Administration Guide

Verify that autoregistration is enabled and is properly configured in Cisco Unified Communications Manager
Administration before you connect any Cisco IP Phone to the network. For information about enabling and
configuring autoregistration, see the documentation for your particular Cisco Unified Communications Manager
release.
Autoregistration must be enabled in Cisco Unified Communications Manager Administration for TAPS to
function.
Procedure
Step 1 In Cisco Unified Communications Manager Administration, click System > Cisco Unified CM.
Step 2 Click Find and select the required server.
Step 3 In Auto-registration Information, configure these fields.
• Universal Device Template
• Universal Line Template
• Starting Directory Number
• Ending Directory Number
Step 4 Uncheck the Auto-registration Disabled on this Cisco Unified Communications Manager check box.
Step 5 Click Save.
Step 6 Click Apply Config.
Related Topics
Cisco Unified Communications Manager Documentation, on page 12
Phone Addition Methods, on page 56
Daisy Chain Mode
You can connect two conference phones using a Smart Adapter and the USB-C cables that are provided in
the daisy chain kit to expand the audio coverage area in a room.
In daisy chain mode, both units receive power though the Smart Adapter which is connected to a power
adapter. You can use only one external microphone per unit. You can use either a pair of wired microphones
with the units or a pair of wireless microphones with the units, but not a mixed combination of the microphones.
When a wired microphone is connected to one of the units, it unpairs any wireless microphones that are
connected to the same unit. Whenever there is an active call, the LEDs and the menu options on the phone
screen of both units are synchronized.
Related Topics
Install the Conference Phone in Daisy Chain Mode, on page 34
One Phone in Daisy Chain Mode Doesn't Work, on page 168
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
27
Cisco IP Conference Phone Installation
Daisy Chain Mode

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g