Cisco 8832 Administration Guide

DescriptionDefaultTypeEntry
Default IPv6 router.
To change this field, turn off DHCP.
IPv6 Default Router 1
Primary IPv6 DNS server
To change this field, turn off DHCP.
IPv6 DNS Server 1
Indicates whether the phone is using an
alternative IPv6 TFTP server.
NoNo
Yes
IPv6 Alternate TFTP
Primary IPv6 TFTP server used that the
phone uses.
See the TFTP Notes section after this
table.
IPv6 TFTP Server 1
Secondary IPv6 TFTP server used that
the phone uses.
See the TFTP Notes section after this
table.
IPv6 TFTP Server 2
NoNo
Yes
IPv6 Address Released
Before IPv6 setup options can be configured on your device, IPv6 must be enabled and configured in Cisco
Unified Communication Administration. The following device configuration fields apply to IPv6 configuration:
• IP Addressing Mode
• IP Addressing Mode Preference for Signalling
If IPv6 is enabled in the Unified cluster, the default setting for IP addressing mode is IPv4 and IPv6. In this
addressing mode, the phone will acquire and use one IPv4 address and one IPv6 address. It can use the IPv4
and the IPv6 address as required for media. The phone uses either the IPv4 or IPv6 address for call control
signalling.
For more information about IPv6, see:
• “Common Device Configuration” in Cisco Unified Communications Manager Feature and Services
Guide, “IPv6 Support in Cisco Unified Communications Devices” chapter.
• IPv6 Deployment Guide for Cisco Collaboration Systems Release 12.0, located here:
https://www.cisco.com/c/en/us/support/unified-communications/unified-communications-system/
products-implementation-design-guides-list.html
TFTP Notes
When the phone looks for the TFTP server, the phone gives precedence to manually assigned TFTP servers,
regardless of the protocol. If your configuration includes both IPv6 and IPv4 TFTP servers, the phone prioritizes
the order that it looks for the TFTP server by giving priority to manually assigned IPv6 TFTP servers and
IPv4 TFTP servers. The phone looks for the TFTP server in this order:
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
41
Cisco IP Conference Phone Installation
Network Setup Fields

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g