EIM TEC2000 - Two Rdms (One 24 Vdc and One 115;208;220;230 Vac Power Source); Table 3-9 Two Rdms Connected to the Actuator

85 pages

To Next Page

To Previous Page

3. Installation

TEC 2000 Installation & Operation Manual E2K-405-0902

3-18

3.8.3. Two RDMs (one 24Vdc and one 115/208/220/230 Vac power source)

To use two RDMs with one actuator, connect as detailed in Table 3-9.

Table 3-9 Two RDMs Connected to the Actuator

RMD RDM Terminal

Block Number

Function TEC 2000

Terminal Block

Number

Cable Type-

Belden or

Equivalent

Line 115/230 Vac 50/60 Hz (+) - 20AWG or Larger

Neu 0V Common - 20AWG of Larger

3 RS-485 (+) 21

1 RS-485 (-) 23

RDM #1

2 Shield 24

Belden 9841

6 24 Vdc 9=0 9

5 0V Common 10

Belden

8719

3 RS-485 (+) 21

1 RS-485 (-) 23

RDM #2

2 Shield 24

Belden

9841

Belde

8723

Main Page

Table of Contents2
Important Notes7
Purpose7
User Safety7
Quick Start8
Set Position Limits8
Figure 2-1 Declutch Lever and Handwheel9
Figure 2-2 Settings Limits - Quick Start10
Network Setup12
Check Settings12
Installation13
Preparing the Stem Nut13
Figure 3-1 Preparing the Stem Nut13
Mechanical Installation Onto the Valve14
Electrical Connections14
Remove Separate Terminal Chamber (STC) Cover14
Sealing Cable/Conduit Entries15
Recommended Terminal Connections15
Figure 3-2 Removal of STC Cover15
Cable Connections16
Replace Terminal Compartment Cover16
External Earth Ground Connections16
Figure 3-3 Power Terminal Connections16
Figure 3-4 Control Terminal Connections16
Display Backup Module (DBM) - Optional17
Figure 3-5 Earth/Ground Connection17
Discrete Controlled Inputs18
Auxiliary Control Module (ACM) - Optional18
Table 3-1 External Power Supply18
Table 3-2 Internal Power Supply18
Wiring the ACM19
Table 3-3 ACM Wiring Connections - Futronic (Analog Control Module)20
Table 3-4 ACM Installation Connections - Controlinc (Network Control Module)21
Analog Controlled - Power Supply Connections22
Figure 3-6 ACM Wiring Connections22
Figure 3-7 Futronic - Analog Input with External Power Supply22
Figure 3-8 Futronic - Analog Input with Internal Power Supply22
Figure 3-9 Futronic - Analog Output with External Power Supply24
Figure 3-10 Futronic - Analog Output with Internal Power Supply24
Figure 3-11 Controlinc - Analog Input with External Power Supply24
Figure 3-12 Controlinc - Analog Input with Internal Power Supply24
Figure 3-13 Controlinc - Analog Output with External Power Supply24
External Variable Frequency Drive Wiring25
Figure 3-14 Controlinc - Analog Output with Internal Power Supply25
Figure 3-15 STC for VFD Applications25
Network Controlled26
Figure 3-16 External VFD Control Wiring26
Auxiliary Relay Module (ARM) Wiring27
Table 3-5 Connecting Actuator a to Actuator B27
Table 3-6 ARM Wiring Connections27
Remote Display Module (RDM) Connection to the Actuator - Optional28
Figure 3-17 ARM Wiring Connections28
Figure 3-18 Connecting RDM Cables to the STC28
24Vdc Power Source29
115/230Vac Power Source29
Table 3-7 RDM Connections with Internal Power Source29
Table 3-8 RDM Connections with External Power Source29
Two Rdms (One 24Vdc and One 115/208/220/230 Vac Power Source)30
Table 3-9 Two Rdms Connected to the Actuator30
Operation31
Local Display Module (LDM)31
Figure 4-1 TEC 2000 Controller31
Graphics Display and Message Center32
Control Knob and Selector Knob32
Figure 4-2 LDM32
Leds33
Normal Display Function33
Table 4-1 LDM Rotating Knobs33
Figure 4-3 Normal Display34
Table 4-2 Normal Display Functions34
Multi-Port Valve Status Display Functions35
Remote Display Module (RDM)35
RDM Operation with LDM35
Table 4-3 "Multi-Port Valve Status" Display Functions35
Infrared Controller (IRC) - "Clicker36
Figure 4-4 "Clicker36
Table 4-4 RDM and LDM Operation Priority36
Initializing the Actuator37
Setting Position Limits37
View Existing Settings38
Table 4-5 Default Configuration Settings39
Local Control Operation41
Figure 4-5 View Settings41
Multi-Port Valve Local Control Mode Operation42
Remote/Auto Control Operation42
Event Logger44
Customizing Actuator Settings45
Entering Setup Mode45
Setting Limits46
Changing Display46
Transferring File Parameters48
Figure 5-2 Change Display48
Computer Requirements49
Installation49
Table 5-1 RS-485 Link Connection49
Displaying Unit Parameters50
Figure 5-3 Displaying Unit Parameters50
Change Settings51
Figure 5-1 Setup52
Figure 5-4 Change Settings52
Passcode Entry53
Valve Control Setup53
Figure 5-5 Passcode Entry53
Figure 5-6 Valve Control Setup54
Set Valve Travel Limits55
Figure 5-7 Set Valve Travel Limits55
Discrete Input Setup57
Figure 5-8 Set Valve Travel Limits for Multi-Port Valve Control Mode57
Discrete Output Setup58
Figure 5-9 Discrete Input Setup58
Table 5-2 Relay Outputs #1 through #5 Configuration59
Table 5-3 Relay Output Function List60
Table 5-4 Solid State Output Relays Configuration60
Figure 5-10 Discrete Output Setup61
Table 5-5 Relay Outputs #9 through #12 Configuration62
Inhibit and ESD Setup63
Figure 5-11 Inhibit and ESD Setup63
Two-Speed Timer Setup64
Analog Setup (Futronic ACM Required)64
Figure 5-12 Two-Speed Timer Setup64
Figure 5-13-1 Analog Setup65
Network Setup (CAM and Controlinc ACM Required)68
Figure 5-14-1 Network Setup69
Tag Name Setup70
Passcode Setup71
Reload Factory Settings71
Figure 5-15 Tag Name Setup71
Figure 5-16 Passcode Setup71
Troubleshooting72
Troubleshooting Problems/Corrective Action for Actuator Operation72
Display Diagnostics74
Figure 6-1 Display Diagnostic75
Display Alarm Log76
Figure 6-2 Display Alarm Log Example76
Display Torque Profile77
Display Torque Archive77
Display Operation Log77
Figure 6-3 Display Torque Profile77
Display Operation Archive78
Figure 6-4 Display Operation Log78
Figure 6-5 Display Operation Archive78
Display Hardware79
Figure 6-6 Display Hardware79
Maintenance81
Maintenance Schedule81
Lubrication81
Pressure Relief81
Fuse Replacement81
Battery Replacement - "Clicker82
Figure 7-1 Fuses in the STC82
Regulatory Information83

EIM TEC2000 - Two Rdms (One 24 Vdc and One 115;208;220;230 Vac Power Source); Table 3-9 Two Rdms Connected to the Actuator

Table of Contents

Related product manuals