To Next Page

To Previous Page

5. Customizing Actuator Settings

TEC 2000 Installation & Operation Manual E2K-405-0902

5-8

5.6. Change Settings

1. Enter “SETUP” mode and use the selector knob (NEXT) to scroll to “CHANGE DISPLAY

SETTINGS?”. Answer “YES.” See Section 5.1, Entering Setup Mode.

2. Enter passcode.

NOTE: A passcode must be entered to change settings.

3. Use the selector knob (NEXT/BACK) to scan the display for the desired setting to change

the following:

?? Valve control setup

?? Valve travel limits

?? Discrete input

?? Discrete output

?? Inhibit and ESD

?? Two-speed timer

?? Analog

?? Network

?? Tag name

?? Passcode

Table of Contents2
Important Notes7
Purpose7
User Safety7
Quick Start8
Set Position Limits8
Figure 2-1 Declutch Lever and Handwheel9
Figure 2-2 Settings Limits - Quick Start10
Network Setup12
Check Settings12
Installation13
Preparing the Stem Nut13
Figure 3-1 Preparing the Stem Nut13
Mechanical Installation Onto the Valve14
Electrical Connections14
Remove Separate Terminal Chamber (STC) Cover14
Sealing Cable/Conduit Entries15
Recommended Terminal Connections15
Figure 3-2 Removal of STC Cover15
Cable Connections16
Replace Terminal Compartment Cover16
External Earth Ground Connections16
Figure 3-3 Power Terminal Connections16
Figure 3-4 Control Terminal Connections16
Display Backup Module (DBM) - Optional17
Figure 3-5 Earth/Ground Connection17
Discrete Controlled Inputs18
Auxiliary Control Module (ACM) - Optional18
Table 3-1 External Power Supply18
Table 3-2 Internal Power Supply18
Wiring the ACM19
Table 3-3 ACM Wiring Connections - Futronic (Analog Control Module)20
Table 3-4 ACM Installation Connections - Controlinc (Network Control Module)21
Analog Controlled - Power Supply Connections22
Figure 3-6 ACM Wiring Connections22
Figure 3-7 Futronic - Analog Input with External Power Supply22
Figure 3-8 Futronic - Analog Input with Internal Power Supply22
Figure 3-9 Futronic - Analog Output with External Power Supply24
Figure 3-10 Futronic - Analog Output with Internal Power Supply24
Figure 3-11 Controlinc - Analog Input with External Power Supply24
Figure 3-12 Controlinc - Analog Input with Internal Power Supply24
Figure 3-13 Controlinc - Analog Output with External Power Supply24
External Variable Frequency Drive Wiring25
Figure 3-14 Controlinc - Analog Output with Internal Power Supply25
Figure 3-15 STC for VFD Applications25
Network Controlled26
Figure 3-16 External VFD Control Wiring26
Auxiliary Relay Module (ARM) Wiring27
Table 3-5 Connecting Actuator a to Actuator B27
Table 3-6 ARM Wiring Connections27
Remote Display Module (RDM) Connection to the Actuator - Optional28
Figure 3-17 ARM Wiring Connections28
Figure 3-18 Connecting RDM Cables to the STC28
24Vdc Power Source29
115/230Vac Power Source29
Table 3-7 RDM Connections with Internal Power Source29
Table 3-8 RDM Connections with External Power Source29
Two Rdms (One 24Vdc and One 115/208/220/230 Vac Power Source)30
Table 3-9 Two Rdms Connected to the Actuator30
Operation31
Local Display Module (LDM)31
Figure 4-1 TEC 2000 Controller31
Graphics Display and Message Center32
Control Knob and Selector Knob32
Figure 4-2 LDM32
Leds33
Normal Display Function33
Table 4-1 LDM Rotating Knobs33
Figure 4-3 Normal Display34
Table 4-2 Normal Display Functions34
Multi-Port Valve Status Display Functions35
Remote Display Module (RDM)35
RDM Operation with LDM35
Table 4-3 "Multi-Port Valve Status" Display Functions35
Infrared Controller (IRC) - "Clicker36
Figure 4-4 "Clicker36
Table 4-4 RDM and LDM Operation Priority36
Initializing the Actuator37
Setting Position Limits37
View Existing Settings38
Table 4-5 Default Configuration Settings39
Local Control Operation41
Figure 4-5 View Settings41
Multi-Port Valve Local Control Mode Operation42
Remote/Auto Control Operation42
Event Logger44
Customizing Actuator Settings45
Entering Setup Mode45
Setting Limits46
Changing Display46
Transferring File Parameters48
Figure 5-2 Change Display48
Computer Requirements49
Installation49
Table 5-1 RS-485 Link Connection49
Displaying Unit Parameters50
Figure 5-3 Displaying Unit Parameters50
Change Settings51
Figure 5-1 Setup52
Figure 5-4 Change Settings52
Passcode Entry53
Valve Control Setup53
Figure 5-5 Passcode Entry53
Figure 5-6 Valve Control Setup54
Set Valve Travel Limits55
Figure 5-7 Set Valve Travel Limits55
Discrete Input Setup57
Figure 5-8 Set Valve Travel Limits for Multi-Port Valve Control Mode57
Discrete Output Setup58
Figure 5-9 Discrete Input Setup58
Table 5-2 Relay Outputs #1 through #5 Configuration59
Table 5-3 Relay Output Function List60
Table 5-4 Solid State Output Relays Configuration60
Figure 5-10 Discrete Output Setup61
Table 5-5 Relay Outputs #9 through #12 Configuration62
Inhibit and ESD Setup63
Figure 5-11 Inhibit and ESD Setup63
Two-Speed Timer Setup64
Analog Setup (Futronic ACM Required)64
Figure 5-12 Two-Speed Timer Setup64
Figure 5-13-1 Analog Setup65
Network Setup (CAM and Controlinc ACM Required)68
Figure 5-14-1 Network Setup69
Tag Name Setup70
Passcode Setup71
Reload Factory Settings71
Figure 5-15 Tag Name Setup71
Figure 5-16 Passcode Setup71
Troubleshooting72
Troubleshooting Problems/Corrective Action for Actuator Operation72
Display Diagnostics74
Figure 6-1 Display Diagnostic75
Display Alarm Log76
Figure 6-2 Display Alarm Log Example76
Display Torque Profile77
Display Torque Archive77
Display Operation Log77
Figure 6-3 Display Torque Profile77
Display Operation Archive78
Figure 6-4 Display Operation Log78
Figure 6-5 Display Operation Archive78
Display Hardware79
Figure 6-6 Display Hardware79
Maintenance81
Maintenance Schedule81
Lubrication81
Pressure Relief81
Fuse Replacement81
Battery Replacement - "Clicker82
Figure 7-1 Fuses in the STC82
Regulatory Information83

Questions and Answers:

Need help?

Do you have a question about the EIM TEC2000 and is the answer not in the manual?

EIM TEC2000 Specifications

General

Brand	EIM
Model	TEC2000
Category	Controller
Language	English

Related product manuals

EIM HQ Series

12 pages

EIM TEC2000 User Manual

Table of Contents

Questions and Answers:

EIM TEC2000 Specifications

Related product manuals