ElectroCraft IQ 2000 - Page 84

3-30 Wiring P/N 0013-1027-005 Rev A
FIGURE 3.30 Expansion Card I/O Connections
NOTICE: THIS PRODUCT REQUIRES IQ
FIRMWARE VERSION 2.00 OR HIGHER
-
+
-
+
OR
OR
O17 (P2)
O24 (P2)
O9 (P1)
O16 (P1)
47
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
O24
O17
O18
O19
O20
O21
O22
O23
I40
I33
I34
I35
I36
I37
I38
I39
I48
I41
I42
I43
I44
I45
I46
I49
W2
OUTPUTS INPUTS
4
P2
+5V
4.7K(16)
470Ù(16)
47Ù(8)
OUTPUTS INPUTS
DIAG, CONNECTION, IQ SERIES
I/O & MEMORY EXPANSION CARD
.XXX±.
0
1
0
DECIMALS.XX±.020
FRACTIONS:±1/64"
DO NOT SCALE DRAWING
UNLESS OTHERWISE SPECIFIED
ANGLES ±1ANGLES °
TOLERANCE ON:
FILLETS AND ROUNDS .02 R MAX
BREAK ALL EDGES .02 MAX
DIMENSIONS ARE IN INCHES
9101-2061
RELIANCE MOTION CONTROL
Confidential Information of
Eden Prairie, MN 55344
DATE DATE
11-19-92
C
PART NO.
DWG SIZE SHEETSCALE
N/A
11
of
REV ECO CHKRDATEREVISION DESCRIPTIONBY
DESIGN ENGRDRAWN BY
OBWJL
12-7-92
20546
JL
7-9-93
SC
B
REV PER ECO
20109
12-7-92
A
JL OBW
RELEASED
W1
OR
OR
I33 (P2)
I48 (P2)
I17 (P1)
I32 (P1)
ALL
EVEN
PINS
2-50
ALL
EVEN
PINS
2-50
OUTPUTS INPUTS
O16
O9
O10
O11
O12
O13
O14
O15
I24
I17
I18
I19
I20
I21
I22
I23
15
8
14
W1 AND W2 ARE PROVIDED TO CONNECT +5V TO P1-49 AND P2-49
RESPECTIVELY.
5
5
6
4
USE 1N914 OR SIMILAR DIODE TO ISOLATE THE BANKS FROM EACH OTHER.
ANALOG CHANNELS NOT AVAILABLE ON I/O BOARD ONLY P/N 9101-2073.
1. P1 & P2 ARE DESIGNED TO CONNECT TO A 24 CHANNEL
NOTES:
OPTO 22 GENERATION 4 I/O MOUNTING RACK THROUGH A 50 PIN
RIBBON CABLE. THE FIRST EIGHT POSITIONS ARE WIRED AS
OUTPUTS, THE LAST 16 POSITIONS ARE WIRED AS INPUTS. USE
OPTO 22 GENERATION 4 I/O MODULES OR EQUIVALENT DESIGNED
FOR 5V LOGIC. THE 5V LOGIC OPERATING VOLTAGE SHOULD BE
TAKEN FROM PINS 6 & 7 OF P3. GENERATION 4 IS A REGISTERED
20777
JL
__
__
D
CORRECTED TYPO IN NOTE 1
TRADEMARK OF OPTO 22.
2. CRIMP CONNECTORS & CONNECTOR HOUSING FOR FIELD WIRING
OF P3 IS INCLUDED AS PART OF KIT. USE 22-28 AWG STRANDED
WIRE. NOISE SENSITIVE APPLICATIONS MAY REQUIRE TWISTED,
SHIELDED PAIR. GROUND SHIELD AT ONE END ONLY.
3. FOR MODULES OTHER THAN OPTO 22 GENERATION 4 OR EQUIVALENT,
DO NOT DRAW MORE THAN 10 mA PER OUTPUT.
10V 10V 10V 10V
.1ÝF.1ÝF.1ÝF.1ÝF
4
6
TO READ 32 BCD THUMBWHEEL SWITCHES IN BANKS OF 4 AT A TIME:
1. SET THE OUTPUT FOR THE ACTIVE BANK ON (LOW), THE OUTPUTS
FOR THE INACTIVE BANKS OFF (HIGH).
2. READ THE OPEN SWITCH POSITIONS AS OFF (HIGH), THE CLOSED
SWITCH POSITIONS AS ON (LOW).
P1
+5V
4.7K(16)
47
49
49
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
470Ù(16)
47Ù(8)
I32
I25
I26
I27
I28
I29
I30
I31
4 CHANNELS OF DIFFERENTIAL MODE ANALOG INPUT TO 12 BIT ADC
ADC2
ADC3
ADC4
ADC5
+5V
NC
NC
NC
6
7
9
10
12
13
5
11
-
+
3
4
1K
1K
1K
1K
1K
1K
1K
1K
100K100K 100K 100K
100K100K 100K 100K
1
-
+
2
P3
-1
-3
-5
-7
-9
-11
-13
-15
BANK 1 BANK 2
BANK 3
BANK 4
BANK 5
BANK 6
BANK 7
BANK 8
-17
-23
-41
-47
-45
-43
-33
-39
-37
-35
-25
-31
-29
-27
-21
-19
20653
JL
10-5-93
BC
C
ADD V2.00 NOTICE