Name: Etel DSC Series
Brand: Etel
Rating: 4 (1 reviews)

To Next Page

To Previous Page

ETEL Doc. - Operation & Software Manual # DSC2P 903 / Ver. F / 3/6/05 Chapter A: Internal functioning & architecture

Operation & Software Manual

Direct Drives & Systems 17

Chapter A:

Internal functioning & architecture

Default Chapter3
- Table of Contents3
Chapter a14
- Chapter a17
1 The Regulators18
2 Current References Generator19
3 Set Point Generator20
- Movements Trajectories Used in the Controller21
4 Controller Timing23
5 Communication with the Controller24
- Multi-Axis Configuration with Micro-Master25
  - Commands & Registers Syntax27
  - Accumulator Operations28
- Registers Groups29
- Register Value Attribution30
- Register Value Reading32
- Bit Fields or Numerical Values for Registers and Commands33
  - Examples of Use34
7 Initial System Installation36
- Configuration with a DSMAX or a DSTEB37
- Controller Setup Principle39
- Install ETEL Tools Software40
8 Controller Setup with ETEL Tools41
- Main Menu Window43
  - Tools Menu44
- Drive Setting Tool45
- Scope Tool54
- Parameters60
15 Commands61
- System Identification62
- Terminal Tool63
  - Read / Send Registers and Commands to the Controller64
- Editor Tool66
  - Download (Create, Open, Modify) Sequences / Registers67
  - Upload (Create, Open, Modify) Sequences / Registers68
- Unit Converter Tool70
  - Unit Conversion71
9 Simplified Regulator's Principle72
- Parameters Description73
- Position Regulator74
10 Controller Regulators Tuning Principle76
11 Save the Settings80
12 Basic Functions and Settings (Necessary to Operate the Controller)82
- Serial Number and Firmware Version83
- Motor84
- Position Encoder85
- Precaution Parameters - IMPORTANT91
- Errors and Warnings Handling97
  - Reset Errors: RST and RSD98
  - Dynamic Braking99
- Basic Reference Mode (K61=1)100
- Initialization101
  - Phasing Processes (K90)104
- Autosetting111
  - PWR Command113
- Homing114
- Basic Movements128
  - Rotary S-Curve Movement130
- Monitorings132
- Controller Software Characteristics133
- Stepper in Open Loop134
13 Advanced Functions (Only for Advanced Users)137
- Regulators Parameters138
- Monitorings Diagram141
- External Reference Modes (K61=0, 3, 4 or 36)143
- Advanced Movements150
- Digital Inputs / Outputs170
  - Digital Outputs172
- Position Capture on Digital Inputs174
  - Description of the Position Capture Process on the Digital Inputs175
- Analog Input / Output176
  - Analog Outputs177
- In-Window181
- RTI: Real-Time Interrupts182
  - RTI Structure183
- RTI Elements Description184
- Controller Parameters and Commands for RTI186
- RTI Process Chart187
- RTI Types188
- RTI Programming Examples192
Triggers194
- Triggers Definition and Structure195
- Masks, Actions Selection198
- Mappings Activation199
Analog Encoder Interpolation202
Status Drive203
- M61 Monitoring (SD2)204
Advanced Communication206
- Real-Time Monitoring (RTM)207
Encoder Scaling and Mapping210
- Encoder Mapping211
- Activation of the Corrections212
Chapter D: Programming213
14 Basic Programming214
- Wait on Bits: WBS and WBC Commands216
- Controller Busy: WTB Command217
- Labels219
- Unconditional Jump: JMP Command220
- Conditional Jump: TST, JEQ, JNE, JLT and JGT Commands221
- Routine Commands: CAL, RET and POP222
- Accumulator Functions223
  - Test XAC Value: IEQ, INE, ILT, IGT, ILE, IGE, JBS and JBC224
- Sequences Handling225
  - Clear User Variables: CLX226
- Mathematical Operations227
- Float Functions229
- Commands Examples & Reference List232
- BRK Example233
- CAL, RET, POP Example234
- CAM Example235
- CLX Example236
- DOUT Example237
- END Example238
- F Registers (Float) Example239
- HLT, HLB, HLO Example240
- JBS, JBC Example241
- JMP Example242
- MMC Example243
- MMD, LTN, LTI Example244
- MMD=3 (Calculated Mvt.), SET Example245
- PWR, IND, ACC, SPD, POS Example246
- REI: RTI Example247
- RSD Example248
- Special Labels (79, 80) Example249
- SLS Example250
- STA Example251
- STE Example252
- STI Example253
- STP Example254
- TCL, TMK, TNB, TRS Triggers Example255
- TST, JGT, JEQ, JNE Example256
- TST, JLT Example257
- WBC, WBS Example258
- WPG, WPL, WSG, WSL Example259
- WTB Example260
- WTM, WTT Example261
- WTP Example262
- WTW Example263
- XAC, IEQ, ILT, IGT Example264
- XAC, IGE, ILE Example265
- XAC, INE Example266
- Commands Reference List267
16 Parameters K277
- Parameters K for DSCDP286
- Parameters K for DSCDL295
- Parameters K for DSCDM303
17 Monitorings M312
- Monitorings M for DSCDP320
- Monitorings M for DSCDL327
- Monitorings M for DSCDM334
18 Warnings Reference Lists341
- Warnings for DSCDM342
19 Errors Reference Lists343
- Errors for DSCDP347
- Errors for DSCDL350
- Errors for DSCDM353
20 Units Conversion357
- Linear Motors358
- Rotary Motors360
- Resolution361
- Current, Force and Torque Units362
- Time Quantities Units363

Other manuals for Etel DSC Series

Hardware Manual43 pages

Questions and Answers:

Need help?

Do you have a question about the Etel DSC Series and is the answer not in the manual?

Etel DSC Series Specifications

General

Brand	Etel
Model	DSC Series
Category	Controller
Language	English

Related product manuals

Etel DSC Series User Manual

Table of Contents

Other manuals for Etel DSC Series

Questions and Answers:

Etel DSC Series Specifications

Related product manuals