Fuji Electric FRENIC MEGA G2 Series - Page 195

5.2 Function Code Tables
5-11
FUNCTION CODES
Chap 5
Function
code
Name
Control method and Data setting range
Change when
running
Data copying
Factory
default
Related page
E10
Acceleration time 2
0.00 to 6000 s
* 0.00 is for acceleration and deceleration time cancel (when
performing soft-start and stop externally)
Y
Y
*1
5-159
E11
Deceleration time 2
Y
Y
*1
E12
Acceleration time 3
Y
Y
*1
E13
Deceleration time 3
Y
Y
*1
E14
Acceleration time 4
Y
Y
*1
E15
Deceleration time 4
Y
Y
*1
E16
Torque limiter 2-1
-300 to 0 to 300%; 999 (Disable)
Y
Y
999
5-159
E17
Torque limiter 2-2
-300 to 0 to 300%; 999 (Disable)
Y
Y
999
E20
Terminal [Y1]
(Function selection)
See E20 to E27 in “Table 5.2.3 Control output terminal setting list table”.
N
Y
0
5-159
E21
Terminal [Y2]
N
Y
1
E22
Terminal [Y3]
N
Y
2
E23
Terminal [Y4]
N
Y
7
E24
Terminal [Y5A/C]
(Ry output)
N
Y
15
E27
Terminal [30A/B/C] function
(Relay output)
N
Y
99
Table 5.2.3 Control output terminal setting list table
Function code and name
Control method and Data setting range
E20 to E27
E71
o23 to o26
o121 to o128
Terminal [Y1]
to [Y4],
[Y5A/C],
[30A/B/C]
Keypad M-
LED indicator
Terminal
[Y1A/B/C] to
[Y4A/B/C]
Terminal [O1]
to [O8]
Y
Y
Y
Y
0 (1000): Inverter running
Y
Y
Y
Y
1 (1001): Frequency (speed) arrival “FAR”
Y
Y
Y
Y
2 (1002): Frequency (speed) detected “FDT”
Y
Y
Y
Y
3 (1003): Under voltage detected (inverter stopped) “LU”
Y
Y
Y
Y
4 (1004): Detected torque polarity “B/D”
Y
Y
Y
Y
5 (1005): Inverter output limiting “IOL”
Y
Y
Y
Y
6 (1006): Auto-restarting after momentary power failure “IPF”
Y
Y
Y
Y
7 (1007): Motor overload early warning “OL”
Y
Y
Y
Y
8 (1008): Keypad operation “KP”
Y
Y
Y
Y
10 (1010): Inverter ready to run “RDY”
Y
N
Y
Y
11: Commercial/inverter power supply switching “SW88”
12: Commercial/inverter power supply switching “SW52-2”
13: Commercial/inverter power supply switching “SW52-1”
Y
N
Y
Y
15 (1015): Switch MC on the input power lines “AX”
Y
Y
Y
Y
16 (1016): Pattern operation stage transition “TU”
17 (1017): Pattern operation cycle completed “TO”
18 (1018): Pattern operation stage 1 “STG1”
19 (1019): Pattern operation stage 2 “STG2”
20 (1020): Pattern operation stage 4 “STG4”
Y
Y
Y
Y
21 (1021): Frequency (speed) arrival 2 “FAR2”
Y
Y
Y
Y
22 (1022): Inverter output limiting with delay “IOL2”
Y
Y
Y
Y
25 (1025): Cooling fan in operation “FAN”
Y
Y
Y
Y
26 (1026): Auto-resetting “TRY”
Y
N
Y
Y
27 (1027): Universal DO “U-DO”
Y
Y
Y
Y
28 (1028): Heat sink overheat early warning “OH”
Y
Y
Y
Y
29 (1029): Master-follower operation complete “SY”