Fuji Electric FRENIC MEGA G2 Series - Page 229

5.2 Function Code Tables
5-45
FUNCTION CODES
Chap 5
Function
code
Name
Control method and Data setting range
Change when running
Data copying
Factory
default
Related page
4001(5001): Terminal [X1] input “X1”
4002(5002): Terminal [X2] input “X2”
4003(5003): Terminal [X3] input “X3”
4004(5004): Terminal [X4] input “X4”
4005(5005): Terminal [X5] input “X5”
4006(5006): Terminal [X6] input “X6”
4007(5007): Terminal [X7] input “X7”
4008(5008): Terminal [X8] input “X8”
4009(5009): Terminal [X9] input “X9”
4010(5010): Terminal [FWD] input “FWD”
4011(5011): Terminal [REV] input “REV”
4021(5021): Terminal [I1] input “I1”
4022(5022): Terminal [I2] input “I2”
4023(5023): Terminal [I3] input “I3”
4024(5024): Terminal [I4] input “I4”
4025(5025): Terminal [I5] input “I5”
4026(5026): Terminal [I6] input “I6”
4027(5027): Terminal [I7] input “I7”
4028(5028): Terminal [I8] input “I8”
4029(5029): Terminal [I9] input “I9”
4030(5030): Terminal [I10] input “I10”
4031(5031): Terminal [I11] input “I11”
4032(5032): Terminal [I12] input “I12”
4033(5033): Terminal [I13] input “I13”
4034(5034): Terminal [I14] input “I14”
4035(5035): Terminal [I15] input “I15”
4036(5036): Terminal [I16] input “I16”
4041(5041): Terminal [CLI1] input “CLI1”
4042(5042): Terminal [CLI2] input “CLI2”
4043(5043): Terminal [CLI3] input “CLI3”
4044(5044): Terminal [CLI4] input “CLI4”
4045(5045): Terminal [CLI5] input “CLI5”
4046(5046): Terminal [CLI6] input “CLI6”
4047(5047): Terminal [CLI7] input “CLI7”
4048(5048): Terminal [CLI8] input “CLI8”
4049(5049): Terminal [CLI9] input “CLI9”
4081(5081): Key RUN/FWD input “KP-RUN/KP-FWD”
4082(5082): Key REV input “KP-REV”
4083(5083): Key STOP input “KP-STOP”
4084(5084): Key UP input “KP-UP”
4085(5085): Key DOWN input “KP-DOWN”
4088(5088): Key M/SHIFT input “KP-M/SHIFT”
4091(5091): Key RESET input “KP-RESET”
4101(5101): Terminal [X1] input (terminal block only) “X1-TERM”
4102(5102): Terminal [X2] input (terminal block only) “X2-TERM”
4103(5103): Terminal [X3] input (terminal block only) “X3-TERM”
4104(5104): Terminal [X4] input (terminal block only) “X4-TERM”
4105(5105): Terminal [X5] input (terminal block only) “X5-TERM”
4106(5106): Terminal [X6] input (terminal block only) “X6-TERM”
4107(5107): Terminal [X7] input (terminal block only) “X7-TERM”
4108(5108): Terminal [X8] input (terminal block only) “X8-TERM”
4109(5109): Terminal [X9] input (terminal block only) “X9-TERM”
4110(5110): Terminal [FWD] input (terminal block only) “FWD-TERM”
4111(5111): Terminal [REV] input (terminal block only) “REV-TERM”
6000 (7000): Final run command RUN “FL_RUN”
6001 (7001): Final run command FWD “FL_FWD”
6002 (7002): Final run command REV “FL_REV”
6003 (7003): Accelerating “DACC”
6004 (7004): Decelerating “DDEC”
6005 (7005): Under anti-regenerative control “REGA”
6006 (7006): Within dancer reference position “DR_REF”
6007 (7007): With/without alarm factor “ALM_ACT”
6100: TRUE (1) fixed input “TRUE”
6101: FALSE (0) fixed input “TRUE”
* Inside the ( ) is the negative logic signal. (OFF at short-circuit).
[Analog]
8000: Output frequency 1 (before slip compensation)
8001: Output frequency 2 (after slip compensation)
8002: Output current
8003: Output voltage
8004: Output torque
8005: Load factor
8006: Power consumption
8007: PID feedback value
8008: Actual speed/estimated speed
8009: DC link bus voltage
8013: Motor output
8015: PID command (SV)
8016: PID output (MV)
8017: Master-follower angle deviation
8018: Inverter cooling fin temperature
8021: PG feedback value
8022: Torque current command
8023: PID deviation
8024: Line speed command
8025: Winding diameter calculation value
8026: Setting frequency (before acceleration/deceleration calculation)
9001: Analog terminal [12] input signal “12”
9002: Analog terminal [C1] input signal (C1 function) “C1”
9003: Analog terminal [V2] input signal “V2”
9004: Analog terminal [32] input signal “32”