Giga-tronics 8003 - Page 256

8003 Precision Scalar Analyzers
Index-4 Manual 20791, Rev. C, June 2001
SERVICE Softkey 2-61
ABORT 2-62, 2-65
CAL LOC 2-64
CHANGE COLOR 2-63
CIRCLES and 1 COLOR 2-63
CLEAR PASSWORD 2-62, 2-65
COLOR BARS 2-63
DEFINE PASSWORD 2-62, 2-64
DONE 2-62, 2-63
ENABLE INPUT 2-64, 2-65
FIRST PAGE and LAST PAGE 2-64
GRID L/S and DOTS L/S 2-63
PAGE UP 2-64
PAGE UP and PAGE DOWN 2-64
PASSWORD 2-64
PROGRAM EEPROM 2-65
SENSOR EEPROM 2-63
SET CAL 2-61
SET CAL OUTPUT 2-61
SET CAL S/N 2-61
SET TIME 2-62, 2-64
TEST PATTERN 2-63
Set the GPIB Address
Programming the 8003 3-2
SHORT/OPEN Softkey
FULL BAND A, B, or C Y/N 2-37
STORE SHORT A, B, or C 2-36
Signal Sources 1-15
SINGLE SENSOR Softkey 2-15
Single-Sensor Insertion Loss Measurement 2-75
Single-Sensor Return Loss Measurements 2-79
Single-Sensor vs Two-Sensor Measurements 2-78
Softkey 2-46
Softkey Functional Description 2-12
Absolute Power & Swept Capabilities 2-13
Channel & Function Selection 2-12
Graph & Readout Display Modes 2-13
Path Calibration Memory 2-13
Power On 2-14
Sensors & Sensor Calibration 2-12
Softkey Labels & Color Indications 2-12
Trace Memory 2-14
Softkey Labels 2-8
Softkey Labels & Color Indications 2-12
SOURCE Controls 2-51
8003 Source Compatibility 2-51
ATE Operation 2-51
General Description 2-51
Key Operation 2-52
UPD SWP ON/OFF 2-52
Span Swept Freq. Source Mode Def. Cmd. Structure 3-67
Special Configurations xv
Specifications 1-7
Accuracy 1-9
Cursors & Markers 1-8
START Key
START, CENTER, and CW 2-52
Start, Center, CW Frequency 2-9
STOP Key
STOP, DF and CW 2-53
Stop, Span 2-8
Structured GPIB Language 3-7
Channel Bias Voltage Definition Command Structure
BIAS 3-12
Channel Definition Command Structure
CHAN, CH 3-13
Command Execution 3-10
Common Structure 3-7
Cursor Definition Command Structure
CURSOR, CUR 3-14
CW Power Measurement Command Structure
POWER 3-36
Fast Step CW Meas. Mode Prg. Example 3-48
Fast-CW Mode Programming Example 3-43
TTL-Triggered Fast-CW Mode Prg. Expl. 3-47
Disable Private Bus Command Structure
DISABLE 3-19
External Status Register Query Command Structure
*ESR? 3-20
Fixed Frequency Source Mode Definition Command
Structure
FIXED 3-21
GPIB/PRIVATE Interface 3-71
Graph Display Definition Command Structure
GRAPH, GPH 3-23
IEEE GPIB Interface Characteristics 3-11
Input Command Structure
INPUT 3-24
Instrument Identifier Command Structure
*IDN? 3-23
Instrument Preset Command Structure
3-18
Key Stroke Emulation Enable/Disable Command
Structure
KEYEM, KE 3-25
Definition of ASCII Codes 3-26
Memory Command Structure
MEMORY 3-29
Plot Command Structure
PLOT 3-33
Plotter Command Programming Example 3-35
Print Definition Command Structure
PRINT 3-49
Readout Display Definition Command Structure
READOUT, TEXT, TXT 3-50
Sensor Calibration Command Structure
CAL 3-12
Sensor Definition Command Structure
SENSOR, SEN 3-51
Sensor Path Calibration Command Structure
THRU, PATH 3-69
Sensor Short/Open Calibration Command Structure
SHORT 3-53
Sensor Zeroing Command Structure
ZERO 3-70
Span Swept Frequency Source Mode Definition
Command Structure
SWPS 3-67
Start/Stop Swept Frequency Source Mode Definition
Command Structure
SWPF 3-64
Update Command Programming Example 3-66
STATUS MESSAGES
488.2 External Status 3-71
488.2 Status Byte 3-70
Swept Measurement Command Structure 3-54
SWP, SWP?
Limit Line Programming Example 3-63
Trace Memory Programming Example 3-61
Temperature & Low Level Offset Update Structure
RDTEMP 3-49
Structured GPIB Language Enable Private Bus Command
Structure
ENABLE 3-19
Sweep in Connector Check 4-11
SWEEP TIME Key 2-56
SWEEP TIME Softkey 2-56
SWEEP TIME Softkey
INT SWP TRIGGER 2-56
Sweeper Installation B-4
GPIB Interconnect Cable Connections B-5
Swept Measurement Command Structure 3-54
SWP, SWP? 3-54
SWPF 3-64
SWPS 3-67
System Configuration
8003 Default Settings B-1
8003 System B-3
Connecting Analyzer to an Instrument Controller B-15
Plotter GPIB Install. Interconnection & Pen Colors B-10
Printer Installation B-6
SYSTEM Controls 2-57
CONFIG Key 2-57
PRESET Key 2-57