Huawei FusionModule500

To Next Page

To Previous Page

Figure 6-14 Removing the transparent cover

Step 2 Remove the SD card.

Figure 6-15 Removing an SD card

Step 3 Remove the monitoring network cable from the camera and remove the camera.

FusionModule500 Smart Mini Data Center

User Manual 6 O&M

Main Page

About this Document3
Table of Contents5
Safety Information11
General Safety11
Personnel Requirements14
Electrical Safety14
Installation Environment Requirements16
Mechanical Safety18
Cooling System Safety20
Battery Safety21
Others24
Overview25
Positioning25
Features27
Typical Application Scenarios and Configurations28
Typical Scenarios28
Typical Configurations28
System Architecture30
Structural System30
Power Supply and Distribution System31
Overview31
Kva UPS32
Power Distribution Subrack33
Optional) Rpdu34
Lithium Battery ESM-48100B134
Cooling System35
Application Conditions35
Technical Specifications36
Management System37
Overview37
System Functions37
Monitoring38
App View38
Alarm38
Historical Data Query39
Linkage Control39
Key Hardware Devices39
ECC800-Pro39
Product Configuration39
Main Control Module41
Power Module50
Environment Monitoring System51
WLDS900 Water Sensor51
Electrode Water Sensor52
T/H Sensor53
Smoke Detector54
Video Management System55
Optional) Camera55
Optional) IVS180056
Optional) VCN51058
Cabinet Electronic Clasp Lock59
Pad61
Optional) Wifi Module62
Optional) Neteco Intelligent Data Center Management System63
System Overview63
Server64
LAN Switch64
Surge Protection and Grounding System65
Surge Protection Solution65
Grounding Solution65
Cable Management66
Installation Guide67
Installation Preparations67
Tools and Instruments67
Installation Environment Check70
Site Equipment Preparation71
Installation Scenarios72
Personnel Requirements73
Hardware Installation73
Cabinet Transportation and Unpacking73
Optional) Removing the Aisle Containment75
Installing a Cabinet79
Installing a Smart Cooling Product81
Materials81
Layout Principles85
Installing an Indoor Unit86
Exhausting Nitrogen from an Indoor Unit87
Installing an Outdoor Unit89
Installation Requirements89
Securing an Outdoor Unit90
Installing a Low-Temperature Component91
Connecting Pipes93
Injecting Nitrogen to Preserve Pressure98
Connecting Water Pipes100
Connecting Cables103
Vacuumization107
Installing Power Supply and Distribution Devices110
Installing Lithium Batteries110
Optional) Installing Busbars111
Installing Pdu2000S112
Installing Monitoring Devices113
Installing the SIM Card and Antenna113
Installing a PAD115
Installing a Remote T/H Sensor for the Smart Cooling Product118
Installing T/H Sensors119
Routing the Cable to a WLDS900 Water Sensor120
Installing an Electrode Water Sensor122
Optional) Installing a Server123
Optional) Installing a Camera125
Optional) Installing a LAN Switch129
Optional) Installing a VCN510130
Optional) Installing an IVS1800136
Cable Routing141
System Cabling Rules142
Grounding the Smart Module146
Cable Connections to the Power Supply and Distribution System146
Top Cable Routing146
Cable Routing Description147
Connecting Cabinet Input Power Cables148
Bottom Cable Routing149
Connecting PDU2000 Power Cables151
Connecting Cables between the Lithium Battery and the UPS153
Management System Cable Connection155
Connecting Cabinet Electronic Clasp Lock Cables155
Connecting Cabinet T/H Sensor Cables156
Connecting VCN Cables157
Connecting IVS1800 Cables158
Connecting a Cable to the WLDS900 Water Sensor159
Verifying the Installation160
Power-On Commissioning163
Power-On Commissioning for the Power Supply and Distribution System163
UPS Power-On Commissioning164
Connecting the Lithium Battery Supply165
Power-On Commissioning for the Cooling System165
Powering on Devices166
Performing Initial Configuration166
Commissioning the Cooling System168
Management System Power-On Commissioning171
Preparations and Webui Login171
Preparations and App Login174
Performing Startup Password Authentication177
How Can I Set the Date and Time179
Adding a Southbound Device179
Creating a Micro-Module Plan View180
Adding a UPS2000G180
Commissioning Sensors181
Setting and Adding a Smoke Detector (Connected to an AI/DI Port on the ECC800-Pro)181
Commissioning a T/H Sensor182
Commissioning the WLDS900 Water Sensor184
Commissioning the Electrode Water Sensor185
Commissioning a Cabinet Electronic Clasp Lock186
Configuring Event Notification190
Video Management195
Preparing Documentation195
Networking Scenario196
Commissioning Cameras (LAN Switch Networking Scenario)196
Commissioning a C3220 Camera196
Commissioning a C3220 Camera (SD Card Configured)202
Commissioning a Network Video Recorder (VCN Scenario)205
Logging in to the OMU Portal205
Initializing Hard Disks206
Setting Parameters on the VCN Webui209
Setting Parameters on the VCN IVS Client212
Commissioning a Network Video Recorder (IVS1800 Scenario)214
Setting Parameters on the IVS1800 Webui215
Setting Parameters on the Iclient218
Linkage Control222
Unlocking the Cabinet Electronic Clasp Lock When a Smoke Alarm Is Generated224
Unlocking the Cabinet Electronic Clasp Lock When a Fire Alarm Is Generated225
Optional) Neteco Management225
Neteco6000 Management226
Connecting a Communications Cable226
Setting Neteco Parameters226
Obtaining the Neteco Software License227
Powering on a Server228
Logging in to the Neteco Client228
Loading a Neteco License229
Installing the NE Mediation230
Adding a Management Domain230
Adding a Smart Module232
Creating an ECC800-Pro on the Neteco236
Cloudopera Neteco Management237
Logging in to the EDCM (Using a Web Client)237
Installing the EDCM App238
Allowing a User to Log in to the EDCM on a Mobile Device239
Optional) Replacing the App Certificate on a Mobile Device239
Logging in to the EDCM App239
Setting EDCM Communication Parameters on the ECC800-Pro240
Connecting to the Network241
Routine Maintenance244
Monthly Maintenance244
Quarterly Maintenance250
Yearly Maintenance257
Troubleshooting267
Power Supply and Distribution System Troubleshooting267
Management System Troubleshooting270
Alarm References272
Parts Replacement274
Replacing Structural System Components274
Replacing a Cabinet Electronic Clasp Lock274
Replacing a Gas Spring275
Replacing a PDU2000276
Replacing Power Supply and Distribution System Components277
Replacing a Surge Protection Module277
Replacing a Fuse279
Replacing a UPS2000-G280
Replacing a Lithium Battery281
Replacing Management System Components282
Replacing an ECC800-Pro Main Control Module282
Replacing an ECC800-Pro PSU283
Replacing an ECC800-Pro Antenna284
Replacing a SIM Card285
Replacing a Camera286
Replacing a VCN510288
Replacing an IVS1800290
Replacing a Hard Disk for the IVS1800291
Replacing a T/H Sensor (33010516)293
Replacing a Smoke Detector294
Replacing a WLDS900 Water Sensor and Water Detection Rope295
Replacing an Electrode Water Sensor298
Technical Specifications299
A Equipment Derating Coefficients300
B Acronyms and Abbreviations301

Huawei FusionModule500

Table of Contents

Other manuals for Huawei FusionModule500

Related product manuals