A
Alyssa StewartAug 26, 2025
What to do if Huawei Storage cable aged?
- MMichelle BrownAug 26, 2025
If you notice that a cable is aged, replace it.
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...What to do if Huawei Storage cable aged?
If you notice that a cable is aged, replace it.
What to do if the battery indicator is blinking on my Huawei Server?
To prevent data loss or damage when the battery indicator blinks and the buzzer buzzes on your Huawei Server, immediately save your data and shut down primary loads. This occurs because the UPS is about to shut down due to insufficient battery reserve. Also, verify that the number of batteries and battery capacity are correctly set based on the actual configuration.
Why is the alarm indicator (yellow) steady on for my Huawei Server?
If the Huawei Server's alarm indicator (yellow) is steady on, it could be due to overtemperature protection, a blocked air channel, or AC input overvoltage or undervoltage protection. To resolve this, increase the cooling capacity of the air conditioner, unblock the air channel, and check whether the AC input is abnormal.
Why is the compressor discharge temperature too high in my Huawei Server?
If the Huawei Server's compressor discharge temperature is too high, it could be due to a blocked refrigerant loop, improperly installed outdoor units, air in the refrigerant loop, a dirty or blocked condenser, a faulty outdoor fan, or insufficient refrigerant. To resolve this, clean the loop and components, install outdoor units correctly, eliminate air from the refrigerant loop and refill refrigerant, clean the condenser fins, check the outdoor fan, and add more refrigerant.
What does it mean when the alarm indicator (red) is steady on in my Huawei Server?
If the Huawei Server's alarm indicator (red) is steady on, it indicates output overvoltage protection or no output due to a PSU fault. If a single PSU is locked out, disconnect the AC input from the PSU, and then power on the PSU again after the indicator turns off. If the fault persists, replace the faulty PSU.
What to do if the Huawei Server UPS does not start?
If the Huawei Server's UPS does not start after pressing the power button, ensure that you press it for more than 5 seconds until you hear a beep. The UPS might also be overloaded, so shut down all loads and restart the UPS.
How to reset the password on a Huawei Server?
If you forget the LCD password for your Huawei Server, and the preset password is 000001, use the feature code (preset to 999999) to activate the LCD password. If you forget both the LCD password and feature code, contact your local Huawei technical support.
Why is the battery discharge time short on my Huawei Server?
If the Huawei Server's battery discharge time is significantly less than the standard time, charge the batteries for more than 8 hours when the mains is normal and test the discharge time again. The battery performance may have deteriorated, so contact your local Huawei technical support to replace the batteries.
Why are the ATS button and automatic modes failing on my Huawei Server?
To address the issue of the Huawei Server's ATS button mode and automatic mode failing, ensure that mains 1 has voltage, rectify the phase sequence of mains 2, replace the fuse if the power source of the motor operation mechanism is abnormal and the control loop fuse has blown and check that the signal cable on the controller is securely connected.
Why is my Huawei Server UPS failing to communicate?
If the Huawei Server's UPS fails to communicate, try reconnecting the UPS communications cable and the UPS parallel cable. If the UPS was deleted on the ECC800 WebUI, remove the Modbus card from the UPS, reinstall it in the corresponding slot, and add the UPS on the ECC800 WebUI.
General| Model | FusionModule800 |
|---|---|
| Form Factor | Modular |
| Power Supply | Dual Hot-swappable Power Supplies |
| Cooling System | In-row cooling or room-level cooling |
| Power Density | High Power Density |
| Deployment Time | Less than 1 week |
| Energy Efficiency | High Energy Efficiency |
| Humidity Range | 5% to 90% (non-condensing) |
| Altitude | Up to 3000 meters |
