IPG Photonics Scanner Series

To Next Page

To Previous Page

Figure 9-7 Locking the Window Assembly

8. If using a scanner that has a Dirty Window Sensor (DWS), reconnect the DWS cable to the

Window Assembly.

Main Page

Table of Contents2
Overview7
Introduction7
Applications7
Features7
Additional Documentation8
Certification8
Class a Digital Device8
Safety Information and Conventions8
EMC Compliance9
Laser Classification9
Safety Labels11
Safety Labels Description and Location12
General Safety Warnings13
Specular Reflections13
Optical Safety13
Limited Express Product Warranties13
Electrical Safety14
Environmental Safety14
Safety Features16
Fiber Interlock16
Additional Safety Resources16
Unpacking Instructions17
Unpacking a Unit from the Shipping Carton17
System Architecture18
Scanners with an IPG Scan Controller18
Scanners with an XY2-100 Interface (MID-Power Scanner Only)19
Product Part Numbers20
MID-Power Scanner Part Number Configurations21
High-Power Scanner Part Number Configurations22
Product Specifications23
MID-Power Scanner23
High-Power Scanner24
High Power Scanner25
Scanner Water Cooling Specifications26
Temperature, Humidity, and Water Cooling Specifications26
Water Connection Overview26
Crossjet/Air Knife Specifications28
Computer Specifications (for Use with IPG Scan Controllers)29
Mechanical Connections and Drawings30
MID-Power Scanner30
MID-Power Scanner with Bayonet Input30
MID-Power Scanner with Collimator Input31
High-Power Scanner32
Mechanical Drawings32
Mass Properties34
Mounting Specification35
IPG Scan Controller36
Fans and Cooling36
MID-Power and 2D High-Power Scanners37
High-Power Scanner38
Fiber Connection39
Overview39
Fiber Installation (HLC and LCA Receivers)39
Fiber Removal (HLC and LCA Receivers)39
Installing Laser with Collimator to MID-Power Scanner with Collimator Input43
Supplementary Equipment/Accessories44
Air Knife Configurations and Mounting44
MID-Power Scanner Mounting44
High-Power Scanner Air Knife Configurations45
High-Power Scanner Mounting45
Installing a Digital Camera47
Overview47
Installation and Setup47
Electrical Connections52
IPG Scan Controller Connections52
Power Supply54
Ethernet57
External Interface57
RS232 Serial58
Scanner Control58
Laser Control59
XY2-100 Connector Description (MID-Power Scanner Only)61
Power Supply62
XY2-100 Digital Signals65
Auxiliary I/O66
Scanner Control66
Laser Connections and Configuration67
Overview67
YLR Series Lasers67
Scan Controller to YLR Series Laser Connections67
YLR Laser Source Setup67
YLS Series Lasers69
Scan Controller to YLS Series Laser (with Hardwire Interface) Connections69
Scan Controller to YLS Series Laser (with Fieldbus Interface) Connections70
YLS Laser Source Setup71
YLPN Series Lasers72
Scan Controller to YLPN Series Laser Connections72
YLPN Laser Source Setup72
External Control Interfaces74
Maintenance75
Overview75
Water Treatment and Corrosion Prevention75
Replacing the Protective Window76
High-Power Scanner Window Replacement Procedure77
MID-Power Scanner Window Replacement Procedure81
Spare Parts List82
High-Power Scanner82
MID-Power Scanner83
Applications84
Introduction84
Overview84
System Recommendations84
Recommended List of Equipment84
Standalone Scanning System (no External Interface)86
Standalone Scanning System Example86
Point and Shoot Processing87
Robotic Point and Shoot Processing87
On-The-Fly (OTF) Processing89
Robotic On-The-Fly Processing89
A Resetting a Scan Controller IP Address through Serial91
B Sentech Ethernet Camera Firmware Update93
C Service and Support96
Technical Support96
B Warranty97
Warranty Limitations97
Limitation of Remedies and Liabilities98
Software98
Firmware License Agreement98
Software License Agreement for Lasernet TM100
Microsoft Corporation Embedded Software End User License Agreement102
C Product Returns107
Returns to the United States107
Shipping Instructions107
Returns to Germany108
Shipping Instructions109

IPG Photonics Scanner Series - Page 80

Table of Contents

Related product manuals