Jasco V-560 - User Manual

Other manuals for Jasco V-560

Hardware/Function Manual48 pages

Questions and Answers

T
Taylor RomeroAug 19, 2025
Why is noise high in Jasco Measuring Instruments?
- S
  Stephanie ChristianAug 19, 2025
  High noise in Jasco Measuring Instruments can occur for several reasons: * The light may not be correctly hitting the center of the entrance slit; if this is the case, adjust the light source mirror. * The spectral bandwidth might be too small; try increasing it. * The absorption of the solvent on the reference beam side may be too high; replace the solvent with a more suitable one. * The lamp may have deteriorated; replace it with a new one.
P
Patricia GuerreroAug 21, 2025
What to do if Jasco Measuring Instrument does not operate?
- L
  Laura SpenceAug 21, 2025
  If your Jasco Measuring Instrument isn't operating, first ensure the power cable is securely plugged into the outlet. If it's disconnected, replug it. If the issue persists, remove the power cable and check the fuse in the main unit. Replace the fuse if it's blown. If the fuse blows immediately after replacement, it indicates a fault in the electrical system.
M
michaelwellsAug 23, 2025
What to do if the light source changeover from WI to D causes a baseline step height of more than 1% in Jasco Measuring Instruments?
- A
  Amanda ManningAug 23, 2025
  If you observe a baseline step height exceeding 1% when switching the light source from WI to D in your Jasco Measuring Instruments, there are several potential causes: 1. The baseline correction might be set to “Off”. Check this setting and set it to “On” if necessary. 2. The light source mirror might be poorly adjusted. Readjust the mirror. 3. The sample chamber might not be securely fitted, causing the beam to hit the cell holder. Ensure the sample chamber is correctly positioned.
T
Tina PhillipsAug 26, 2025
Why is the baseline curved greatly in excess of 1% on Jasco Measuring Instruments?
- J
  Jennifer MooreAug 26, 2025
  A greatly curved baseline (in excess of 1%) in Jasco Measuring Instruments may be due to the baseline correction being set to “Off”. Check this setting and set it to “On”.
M
Mrs. Jamie Berger MDAug 27, 2025
How to fix unstabilized performance at wavelengths shorter than 320 nm on Jasco V-560?
- B
  Brandon ChapmanAug 28, 2025
  If the performance at wavelengths shorter than 320 nm is not stabilized on your Jasco Measuring Instruments, the D lamp might be “Off”. Set the D lamp to “On.”
R
ramosemilyAug 29, 2025
How to fix unstabilized performance at wavelengths longer than 400 nm on Jasco V-560 Measuring Instruments?
- M
  mannconnieAug 29, 2025
  If the performance at wavelengths longer than 400 nm is not stabilized on your Jasco Measuring Instruments, the WI lamp might be “Off”. Set the WI lamp to “On.”
D
Dr. John Taylor MDSep 1, 2025
What to do if WI lamp does not light in Jasco V-560?
- M
  Michael FisherSep 1, 2025
  If the WI lamp does not light in your Jasco Measuring Instruments, check if the lamp has burnt out. If it has, replace it with a new one.
J
Jacob AndersonSep 3, 2025
What to do if Jasco V-560 do not operate at all?
- J
  Joshua VargasSep 3, 2025
  If the Jasco Measuring Instruments do not operate, first, check if the power cable is securely plugged into the outlet; if disconnected, replug it. If the issue persists, remove the power cable and check the fuse in the main unit. If the fuse is blown, replace it. If the fuse blows immediately after replacement, the electrical system is faulty.
N
Nicole KramerSep 5, 2025
Why is there high noise in Jasco Measuring Instruments?
- A
  Ann MorseSep 5, 2025
  High noise in Jasco Measuring Instruments can occur because the light is not correctly incident upon the center of the entrance slit. If this is the case, you should adjust the light source mirror. Also, high noise may be caused by a spectral bandwidth that is too small, so try increasing the spectral bandwidth. Another reason can be that the absorption of the solvent placed on the reference beam side is too high, in this case replace the solvent with a suitable one. Finally, high noise may appear because the lamp has deteriorated, you should replace it with a new one.
I
Isabella PerkinsSep 7, 2025
What to do if the WI lamp does not light in Jasco Measuring Instruments?
- M
  maldonadoluisSep 7, 2025
  If the WI lamp does not light in Jasco Measuring Instruments, check if the WI lamp has burnt out. If it has, replace the lamp with a new one.