Juniper EX2300-C Hardware Guide

NOTE: After you insert a transceiver or after you change the media-type
configuration, wait for 6 seconds for the interface to display the operational
commands.
Use only optical transceivers and optical connectors purchased from Juniper Networks
for your EX Series switches.
•
For the list and specifications of transceivers supported on EX2200 switches, see
Pluggable Transceivers Supported on EX2200 Switches.
•
For the list and specifications of transceivers supported on EX2300 switches, see
“Pluggable Transceivers Supported on EX2300 Switches” on page 73.
•
For the list and specifications of transceivers supported on EX3200 switches, see
Pluggable Transceivers Supported on EX3200 Switches.
•
For the list and specifications of transceivers supported on EX3300 switches, see
Pluggable Transceivers Supported on EX3300 Switches.
•
For the list and specifications of transceivers supported on EX3400 switches, see
Pluggable Transceivers Supported on EX3400 Switches.
•
For the list and specifications of transceivers supported on EX4200 switches, see
Pluggable Transceivers Supported on EX4200 Switches.
•
For the list and specifications of transceivers supported on EX4300 switches, see
Pluggable Transceivers Supported on EX4300 Switches.
•
For the list and specifications of transceivers supported on EX4500 switches, see
Pluggable Transceivers Supported on EX4500 Switches.
•
For the list and specifications of transceivers supported on EX4550 switches, see
Pluggable Transceivers Supported on EX4550 Switches.
•
For the list and specifications of transceivers supported on EX4600 switches, see
Determining Interface Support for an EX4600 Switch.
•
For the list and specifications of transceivers supported on EX6200 switches, see
Pluggable Transceivers Supported on EX6200 Switches.
•
For the list and specifications of transceivers supported on EX8200 switches, see
Pluggable Transceivers Supported on EX8200 Switches.
•
For the list and specifications of transceivers supported on EX9200 switches, see
Pluggable Transceivers Supported on EX9200 Switches.
Related
Documentation
Installing a Transceiver on page 193•
• Removing a Transceiver on page 195
• Connecting a Fiber-Optic Cable on page 170
Copyright © 2017, Juniper Networks, Inc.98
EX2300-C and EX2300 Switches Hardware Guide

Juniper EX2300-C Specifications

General

Safety	UL-UL60950-1, C-UL CAN/CSA 22.2 No.60950-1, TUV/GS EN 60950-1, CB-IEC60950-1, EN 60825-1
Form factor	1U
Product color	Black
Rack mounting	Yes
Electromagnetic compatibility	FCC 47CFR 15 A, EN 55022 A, ICES-003 A, VCCI A, AS/NZS CISPR 22 A, EN 55024, EN 300386, CE
Console port	USB
SFP+ module slots quantity	2
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	12
Number of VLANs	4093
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ah, IEEE 802.3u, IEEE 802.3z
Virtual LAN features	Tagged VLAN, Port-based VLAN
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 1000BASE-T
Power consumption (max)	20 W
Memory type	DRAM
Noise level	0 dB
Flash memory	2000 MB
Processor frequency	1250 MHz
Virtual stacking (units)	4
Operating altitude	0 - 1524 m
Non-operating altitude	1524 - 4877 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 85 %
Throughput	47 Mpps
Jumbo frames	9216
MAC address table	16000 entries
DHCP features	DHCP server, DHCP client
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, HTTPS, SNMP, SSH-2
Fiber ethernet cabling technology	1000BASE-X
Switch type	Managed
Switch layer	L2/L3

Weight and Dimensions

Depth	239 mm
Width	279 mm
Height	44 mm
Weight	2480 g