EasyManuals Logo

Juniper EX2300-C Hardware Guide

Juniper EX2300-C
294 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #251 background imageLoading...
Page #251 background image
CHAPTER 21
Fire Safety Requirements
Fire Safety Requirements on page 229
Fire Safety Requirements
In the event of a fire emergency, the safety of people is the primary concern. You should
establish procedures for protecting people in the eventof a fire emergency, provide safety
training, and properly provision fire-control equipment and fire extinguishers.
In addition, you should establish procedures to protect your equipment in the event of a
fire emergency. Juniper Networks products should be installed in an environment suitable
for electronic equipment. We recommend that fire suppression equipment be available
in the event of a fire in the vicinity of the equipment and that all local fire, safety, and
electrical codes and ordinances be observed when you install and operate your equipment.
Fire Suppression
In the event of an electrical hazard or an electrical fire, you should first turn power off to
the equipment at the source. Then use a Type C fire extinguisher, which uses noncorrosive
fire retardants, to extinguish the fire.
Fire Suppression Equipment
Type C fire extinguishers, which use noncorrosive fire retardants such as carbon dioxide
and Halotron™, are most effective for suppressing electrical fires. Type C fire extinguishers
displace oxygen from the point of combustion to eliminate the fire. For extinguishing fire
on or around equipment that draws air from the environment for cooling, you should use
this type of inert oxygen displacement extinguisher instead of an extinguisher that leaves
residues on equipment.
Do not use multipurpose Type ABC chemical fire extinguishers (dry chemical fire
extinguishers). The primary ingredient in these fire extinguishers is monoammonium
phosphate, which is very sticky and difficult to clean. In addition, in the presence of minute
amounts of moisture, monoammonium phosphate can become highly corrosive and
corrodes most metals.
Any equipment in a room in which a chemical fire extinguisher has been discharged is
subject to premature failure and unreliable operation. The equipment is considered to
be irreparably damaged.
229Copyright © 2017, Juniper Networks, Inc.

Table of Contents

Other manuals for Juniper EX2300-C

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper EX2300-C and is the answer not in the manual?

Juniper EX2300-C Specifications

General IconGeneral
SafetyUL-UL60950-1, C-UL CAN/CSA 22.2 No.60950-1, TUV/GS EN 60950-1, CB-IEC60950-1, EN 60825-1
Form factor1U
Product colorBlack
Rack mountingYes
Electromagnetic compatibilityFCC 47CFR 15 A, EN 55022 A, ICES-003 A, VCCI A, AS/NZS CISPR 22 A, EN 55024, EN 300386, CE
Console portUSB
SFP+ module slots quantity2
Installed SFP modules quantity0
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity12
Number of VLANs4093
Networking standardsIEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ah, IEEE 802.3u, IEEE 802.3z
Virtual LAN featuresTagged VLAN, Port-based VLAN
Copper ethernet cabling technology10BASE-T, 100BASE-TX, 1000BASE-T
Power consumption (max)20 W
Memory typeDRAM
Noise level0 dB
Flash memory2000 MB
Processor frequency1250 MHz
Virtual stacking (units)4
Operating altitude0 - 1524 m
Non-operating altitude1524 - 4877 m
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 85 %
Throughput47 Mpps
Jumbo frames9216
MAC address table16000 entries
DHCP featuresDHCP server, DHCP client
AuthenticationMAC-based authentication, Port-based authentication
Security algorithms802.1x RADIUS, HTTPS, SNMP, SSH-2
Fiber ethernet cabling technology1000BASE-X
Switch typeManaged
Switch layerL2/L3
Weight and Dimensions IconWeight and Dimensions
Depth239 mm
Width279 mm
Height44 mm
Weight2480 g

Related product manuals