PWR-01 9
No
.
Name Function
1POWER switch
Press the ( ) side to turn on and the ( ) side to turn off.
p.28, p.29
2 Voltmeter Displays the voltage, alarm, or CONFIG parameter number. p.34, p.54
3OUTPUT LED
Lights green when output is turned on. Blinks orange during output-on delay. Blinks
green during output-off delay.
p.37
Blinks orange when output is on and a protection function is activated. p.46
Lights green during soft start. Blinks green during soft stop. p.39
4 Ammeter
Displays the current, power, or the cause of an alarm, or the value of a CONFIG param-
eter.
p.34, p.46,
p.54
5 OUTPUT key Used to turn output on and off. p.37
6 VIR/ SS/ DLY/ SEQ/ HB
VIR: Lights when the variable internal resistance function is enabled.
SS: Lights when the soft start/ stop function is enabled and blinks when it is in progress.
DLY: Lights when the output-on/ off delay is enabled and blinks when it is in progress.
SEQ: Lights when a sequence is being executed and blinks the PWR-01 is waiting for a
trigger.
HB: Lights when the hyper bleeder of the bleeder circuit is enabled.
p.78
p.39
p.38
p.79
p.76
7 PRESET A/ B/ C LED
A: Lights green when the memory A values are being recalled or saved.
B: Lights green when the memory B values are being recalled or saved.
C: Lights green when the memory C values are being recalled or saved.
p.70
8
SET key Used to set and confirm the output voltage and output current (the key has an LED). p.34
ALM CLR key Used to release the activated state (alarm) of protection functions (the key has an LED). p.46
9
OVP•OCP key
Used to set and display the overcurrent protection (OCP), overvoltage protection (OVP),
undervoltage limit (UVL) trip points (the key has an LED).
p.47, p.52
SC1 Used to call the CONFIG parameter shortcut (the key has an LED) p.72
10
CONFIG key Used to configure the various operating conditions (CONFIG) (the key has an LED). p.54
SC2 Used to call the CONFIG parameter shortcut (the key has an LED) p.72
11
VOLTAGE knob Used to set the voltage value or select the value of a CONFIG parameter. p.36, p.54
FINE Used to make fine voltage value adjustments. p.36
12 CV LED Lights green during constant voltage mode. p.45
13 CC LED Lights red during constant current mode. p.45
14
CURRENT knob
Used to set the current, change the value of a CONFIG parameter, or set the internal
resistance value.
p.36, p.54,
p.59
FINE Used to make fine current or internal resistance value adjustments. p.36, p.59
15
ALM LED
Lights red when a protection function is activated. However, when the undervoltage limit
(UVL) is activated, the LED does not light. When the power limit (POWER LIMIT) is acti-
vated, the LED blinks.
p.71
RMT LED Lights green when the PWR-01 is being remotely controlled p.73
LOCK LED Lights green when the keys are locked. p.71
LAN LED
Lights and blinks when the LAN interface is running.
• No fault status (green)
• Fault status (red)
• Standby status (orange)
• Identify status (blinking green)
Communica-
tion Interface
Manual
16
LOCAL key
Used to switch between local mode and remote mode (the key has an LED) and switch
the CONFIG parameter display.
p.73
SHIFT key Used to enable the functions that are written in blue characters below the key. –
17
PWR DSPL key Used to display the output power on the ammeter (the key has an LED). p.34
LOCK key
Used to lock the operation of all keys other than the OUTPUT key (key lock) (the key has
an LED).
p.71
18
MEMORY key Used to load and save the value of preset memory A, B, or C (the key has an LED). p.70
SC3 Used to call the CONFIG parameter shortcut (the key has an LED). p.72
19 Air inlet (louver) Air inlet for cooling. p.116
20 DC OUTPUT connector Front-panel output terminal. p.27
21 Rubber feet Four locations on the bottom side. p.139
22 Handle Handle for carrying. p.139
To Next Page
Loading...
