Lorex ECO 2 - User Manual

Questions and Answers

A
April MartinezAug 18, 2025
Why I cannot connect to Lorex DVR on a local network?
- B
  bridget50Aug 18, 2025
  If you're unable to connect to your Lorex DVR on a local network, here are a couple of things to check: * Ensure the DVR is connected to the router using an Ethernet cable from the DVR LAN port. After connecting, reset the DVR using the power switch. * Verify that both your DVR and computer are on the same network. If your computer is using WiFi, try connecting it to the router with an Ethernet cable.
K
Kimberly MelendezAug 21, 2025
How to disable the beeping sound during motion detection on my Lorex DVR?
- S
  Sergio EspinozaAug 22, 2025
  If your Lorex DVR system beeps during motion detection, it's likely because motion detection is enabled and the alarm buzzer is activated. To turn it off, open the Main Menu and click System>Motion. In the Buzzer drop-down, select Off, and then click apply.
B
Bridget YatesAug 25, 2025
What to do if the hard drive is not detected by my Lorex ECO 2 system?
- D
  David BallAug 26, 2025
  If the hard drive is not being detected by your Lorex DVR system, the issue might be: * Loose or improperly connected hard drive cables. To solve this, remove the housing and check that hard drive cables are firmly connected. * The absence of a hard drive in the system. If this is the case, open the housing and install a 3.5" SATA hard drive. Remember to format the drive after installation.
M
Melissa CarterAug 27, 2025
Why is there no picture on selected channels of my Lorex DVR?
- J
  Joseph FuentesAug 28, 2025
  If there's no picture on selected channels, or if the camera picture isn't being displayed on your Lorex DVR, it might be due to loose or disconnected camera cables. Check the camera video cable and connections, disconnect and reconnect the cable at both the system and the camera. You might also try moving the camera to another channel or using a different cable.
M
Miss Peggy RiversAug 31, 2025
What to do if the hard drive is full and my Lorex ECO 2 is no longer recording?
- D
  Debra SandersAug 31, 2025
  If your Lorex DVR's hard drive is full (0%) and it's no longer recording, the 'Overwrite' function may not be enabled. To fix this, go to the Main Menu, select DEVICE HDD, and then select 'Auto' under 'Overwrite'.
D
Donald SmithSep 3, 2025
How to troubleshoot a Lorex ECO 2 that is not receiving power?
- B
  Brittany GrahamSep 3, 2025
  If your Lorex DVR system isn't receiving power or powering up, here's what you can check: * Ensure the cable from the power adapter is securely connected to the back of the unit and that all cables are connected correctly. * Verify that the power switch is in the ON (I) position. * Confirm the system is powered on by checking for LED indicators on the front. If connected through a power bar or surge protector, try connecting directly to a wall outlet. Also, test the outlet with another device to confirm it's providing power.
B
Brian SmithSep 5, 2025
What to do if the mouse is not detected by Lorex ECO 2 system?
- E
  Evan GarciaSep 5, 2025
  If the mouse is not being detected by your Lorex DVR system, try the following: * Ensure the mouse cable is firmly connected to the USB Mouse port on the front panel. * If the issue persists, power off the system (disconnect the power cable). Then, firmly connect a USB mouse to the USB Mouse port on the front panel and reconnect the power cable to the DC 12V port on the rear panel.
E
Elaine MillerSep 8, 2025
Why does my Lorex DVR have video but no sound?
- S
  samanthabanksSep 8, 2025
  If the image on your Lorex DVR appears but there is no sound, check the following: * Ensure the AUDIO Input connections to the DVR are securely connected. * If you're using external speakers, make sure their volume is turned up.
C
Caleb VegaSep 12, 2025
What to do if the remote control is not detected by my Lorex ECO 2 DVR?
- D
  dennismcdonaldSep 12, 2025
  If the remote control is not being detected by your Lorex DVR system, the battery in the remote control may be drained. Install two fresh AAA alkaline batteries in the remote control.
D
Debbie SandersNov 15, 2025
What to do if there is no picture on my monitor/TV after connecting it to Lorex ECO 2?
- E
  Elizabeth HooverNov 15, 2025
  If you're not seeing a picture on your monitor/TV after connecting it to the Lorex DVR, there are several potential causes and solutions: * The monitor/TV may not be detected by the DVR. To resolve this, power off both the monitor/TV and the DVR. Then, power on the monitor/TV first, followed by the DVR. * The input channel for the DVR may not be selected on the monitor/TV. Make sure to select the correct input channel on your monitor/TV to which the DVR is connected. * The video cable might be loose or disconnected. Check the video cable connection at both the DVR and the monitor/TV to ensure it's secure. * The video-out resolution may be set incorrectly. To reset it to the default resolution (1024x768), press and hold the button labeled '?' on the front panel of the DVR until it ...