Matrot M24D Hellios - 5.6. Extending; retracting the booms

102 pages

Save Page as PDF

To Next Page

To Previous Page

42 2011

User notice

M24D Hellios

V 1.0

5.6. Extending / retracting the booms

Main Page

Foreword3
Scope3
General Safety Instructions3
Products Implemented4
Warranty4
Miscellaneous4
Pictograms5
Identification of the Self-Propelled Machine6
Table of Contents8
Safety11
Safety Stickers11
Safety Hammer16
General Safety Information16
Technical Characteristics17
General Description of M24D Hellios18
Controls20
Operating the Self-Propelled Machine23
Adjusting the Steering Wheel23
Adjusting the Seat23
Lighting and Indications24
Adjusting the Rear View and Wing Mirrors25
Heating and Air Conditioning26
Control Panel26
On/Off26
Digital Screen26
Temperature Sensor26
Setpoint27
Ventilation27
Air Conditioning and Heating28
Demisting, De-Icing29
System Parameters30
Brakes31
Hydrostatic Brake31
Foot Brake31
Parking Brake31
Starting the Engine32
Pre-Start Checks32
Filling with Diesel33
Starting the Engine33
Start-Up33
Causes of Incorrect Start-Up34
Engine Speed34
Monitoring the Engine34
Movement34
Selecting Speeds34
Stopping the Engine36
Towing37
Rear Steering38
Driving on the Road38
Driving in Fields39
Quick Repairs for Rear Steering41
Extending / Retracting the Booms42
Extending the Booms43
Retracting the Booms45
Maintenance46
Hydrostatic Transmission46
Filtration Filtration46
Top up with Oil and Check Level47
Precautions after Changing Filter Cartridges or Oil48
Practical Tips49
Adjusting Hydraulic Pressure50
The Distribution Unit >(Lifting, Extension & Retraction of Booms; Deployment, Slopes)50
The Spray Pump Control Distributor (Photo 87)50
Hydrostatic Pump (Forward Movement)51
Adjusting Up/Down Speed51
Adjusting Boom Extension Speed and Slope Correction51
Pump and Engine Pressure Tap52
Connections Circuit52
Mechanical Transmission53
Driving Axle (Ground Clearance = 1 M, Depending on the Tyre Fitting)53
Driving Axle (Ground Clearance = 1.3 M or 1.6 M, Depending on the Tyre Fitting)54
Transfer Gearbox54
Assisted Front Axle55
Motor56
Recommended Lubrication56
Drainage Period56
Air Filter57
Oil Filter58
Fuel Filters58
Exhaust and Intake Manifold Connectors59
Engine Cooling System59
Type of Oil and Capacity60
Motor60
Transmission Components60
Greasing61
Relays and Fuses66
Filtration68
Air Circuit69
Suspension69
Table of Tyre Fittings71
M24D Hellios 25 Km/H Tyre Fittings71
M24D Hellios 40 Km/H Tyre Fittings72
Spraying73
Filling and Incorporation (by External Suction)77
Direct Filling (Liquid Fertiliser) - Position 3B80
Intensive Mixing - Position 1A + R081
Mixing and Spraying - Position 1 a81
Spray Arms (Rinsing Tank Suction) - Position 5 C82
Spray Arms (Main Tank Suction) - Position 5 a82
Transfer (Main Tank to External Tank) - Position 4 a82
Suction Filter Cleaning - 4 D83
Drainage of the Main Tank Using the Manual Valve84
Basic Information on Drift85
Winter Storage85
Cleaning the Spray87
Washing the Self-Propelled Machine after Use87
Cleaning Nozzles87
Checking Nozzle Flow87
Inter-Operation Storage88
How to Order Parts90
Options91
Rear Jet Option91
Residual Volume Spray Option92
Cab-Controlled Residual Volume Dilution Option93
Section Cutout Using the Joystick94
Weather Station94
DGPS-Assisted Self-Steering and Section Cutout94
Deutz Liquid Crystal Display95
General Description95
Instruction Manual96
Adjusting Brightness and Contrast96
Using Keys96
Main Mode Display96
4-Screen Mode Display97
Graphic Mode Display98
Parameters Which Can be Selected in Graphic Mode and Display of Engine Failures and Failure Codes98
Configuration (Access Code 1111)100

Matrot M24D Hellios - 5.6. Extending; retracting the booms

Table of Contents