10/05 AWB8230-1541GB
Keypad
57
Setting the display parameters
By default, the digital display indicates the output frequency (Hz
LED is lit). The following section lists the other operational data
that can be displayed.
X Press the PRG key. The display indicates PNU d001 (output
frequency).
X To change to the next display parameter ( PNU d002 = motor
current) press the arrow key Í.
When you have selected a display parameter (d…), press the PRG
key, to display that parameter’s value. Parameter and selected
indication are not saved. To save the display parameter (d...) (not
the selected indication), press first the ENTER key and then PRG.
To save the display form, press first the PRG key and then ENTER.
Display parameters d080 to d083 show the identified faults. For
each fault signal a fault register entry containing the operational
data at the time of the fault (current, voltage, frequency, etc.) is
created. You can call up the fault register with the PRG key and the
associated operational data with the arrow keys (a section
“Fault register”, page 120).
Table 18: Indication parameter
h
You can call up the parameters of the display menu (d…)
in both RUN- and STOP mode.
h
The selected display parameter (d…, PNU) is
automatically saved in the event of a mains power failure
or disconnection and is displayed again when power is
restored.
If the PNU value you have selected is to be shown again
the next time the device is switched on, press the ENTER
key to save it before switching off.
h
If frequency inverter DF51 is connected to a field bus
(CANopen, PROFIBUS DP) or an external keypad through
the serial interface, use PNU b89 to call up the display
parameters.
PNU Name Function
d001 Output frequency display Displays the output frequency in Hertz (Hz). The Hz LED is lit.
d002 Output current display Displays the output current in amperes (A). The A LED is lit.
d003 Direction of rotation display Display:
• F for clockwise operation (forward),
• r for anticlockwise operation (reverse),
•
o for stop
d004 PID feedback display Indication in % if PID control enabled. The factor is set with PNU A075. Default is 0.00.
d005 Indication – status of digital
inputs 1 to 5
Example: Digital inputs 1, 3 and 5 are activated. Digital inputs 2 and 4 are
deactivated. Digital inputs 2, 4 and 6 are disabled.
d006
Indication – status of digital
outputs 11 and 12, and relay K1
Example: Digital output 11 and relay output (N/O contact K11-K14) are
enabled. Digital output 12 is disabled.
d007
Indication of scaled output
frequency
Indication of the product of the factor (PNU b086) and the output frequency.
Examples:
• Maximum output frequency 50 Hz
• Factor PNU b086 = 25
• Indication 1500, corresponds with the synchronous speed of a four-pole motor.
d013
Indication – output voltage indication of motor voltage at 50 Hz in volts (V).
d016 Indication – operation time
counter
Total time in hours in which DF51 is in RUN operation.
d017 Indication – mains On time Total time in hour in which DF51 was live (mains, internal DC link) (Power display).
d080 Indication – total number of
occurred faults
Total number of detected fault signals (E…).
d081 Indication – fault 1 (last fault
signal)
Indication of last fault signal. The fault register contains the operational data (current, voltage,
frequency, etc.) at the time of the fault.
d082 Indication – fault 2 Display of fourth from last fault message. The fault register contains the operational data (current,
voltage, frequency, etc.) at the time of the fault.
d083
Indication – fault 3 Display of third from last fault message. The fault register contains the operational data (current,
voltage, frequency, etc.) at the time of the fault.
564321
K14 12 11
To Next Page
Loading...
