NeuraLabel Callisto

To Next Page

To Previous Page

5-22

is achieved with a smaller gap, but print speeds are slower. Continuous Copies is a printer

feature that is activated through the features view. For more information about using the

Callisto as a Web Press in this mode, contact NeuraLabel.

Main Page

Table of Contents6
Setting up the Printer14
Tour of the Callisto Printer16
Callisto Printing Technology16
Callisto Printer Media Entrance Side16
Callisto Printer Media Exit Side17
Callisto Printer Back Side18
Callisto Consumables20
Ink20
Ink Status20
Ink Access22
Service Tray23
Service Tray Status24
Service Tray Access24
Label Media26
Setting up the Network28
Working with Labels and Media32
Loading Media32
Jogging Media32
Unloading Media32
Sending a Print33
Print Job Continuation33
Die-Cut Labels33
Printing as a Web Press34
Installing the Printer Driver36
Special Case Driver Installation38
Setting up and Using the Printer Driver40
Set Printing Defaults40
Quality Tab41
Normal Print Quality41
Draft Print Quality42
Best or Max DPI Print Quality42
Label Form Tab43
Page Creation43
Borderless Printing, Overspray and Underspray45
Media Type and Orientation45
Label Placement Tab46
Print and Mark Modes46
Continuous Direction Label Placement46
Non-Continuous Direction Label Placement47
Start of Print48
Presentation and Cut Tab48
Auto Present48
Cut after Present49
Job Holding49
Job Attributes Tab49
Callisto Operator Panel52
Home Screen52
Home Icon52
Time52
Media Present Indicator52
Network Address52
Jog and Pause Buttons52
Printer Status52
Printer Icons54
Supplies54
Reports54
Device Information55
Device Statistics55
Print Quality Report56
Network Settings56
Event Logs57
Print Settings58
Device Settings60
Preferences61
Mark/Gap Settings61
Vacuum Control63
Printer Features63
Label Cost Calculator63
Vision Portal by Reliance Label Solutions, Inc64
Roll to Roll Continuous Copies64
Printer Statistics Module65
Rotate 180 (300X Driver)65
Job Continuation65
Collate65
Clean Printhead Maintenance Routine66
Die Leveling Maintenance Routine68
Die Alignment Maintenance Routine70
Nozzle Management Maintenance Routine72
Service Tray72
Remove Service Tray72
Install Service Tray73
Check Service Tray74
Advance Service Tray74
Callisto Troubleshooting Menu74
Calisto Printer Updates75
Advanced Support Tools76
Rest Commands77
Printhead Height77
Set Custom Printhead Height77
Use Custom Printhead Height78
Printer Controller79
Reset79
Job Log80
Job Queue81
Held Jobs82
Callisto Web Server84
Web Interface Home84
Maintenance Quality Toolbox85
Die Leveling85
Die Alignment86
Printhead Height86
Settings87
Reports88
Support Tools92
Print Jobs93
10. Printing Labels96
Printing Your First Labels96
Setting up the Label96
Determining the Media Size96
Creating the Label Page Size in the Driver97
Determining the Image or Artwork Size97
Ordering Media from Neuralabel97
Fine Sizing of the Label Page98
Selecting Driver Parameters98
Set the Label Form Settings Media Type and Orientation98
Select Labels, Gap or Mark and Offsets for Label Placement Settings99
Set the Speed99
Select the Printhead Height100
Loading Media into the Printer100
Making a Sample Print100
Printing the Label Job101
Printing Workflows101
Canceling a Job101
Clearing a Label Jam in the Printer103
Changing an Ink Cartridge104
Running out of Media During the Print105
11. Troubleshooting106
Driver Fails to Install106
Print Does Not Start106
Print Does Not Start at Correct Position (Top of Form)106
Printer Stops Printing in Middle of Print106
Media will Not Load107
Printer Does Not Detect Media107
Printer Prints at Wrong Speed107
Width or Length Is Not Correct107
Print Is too Dark/Print Is too Light107
Print Disappears from Job Queue107
Print Prints Blank Pages108
Print Prints on Every Other Label108
Printer Is Unresponsive, Status Says Printing with no Activity108
Label Is Stuck in Printer108
Printing Copies from Microsoft Word Gives Trouble109
12. Index110

NeuraLabel Callisto - Page 35

Table of Contents

Other manuals for NeuraLabel Callisto