Oki B6200 - Page 26

1 - 10
Chapter 1 Troubleshooting
004 363 Main Motor fail of rotation
Main Motor fail of rotation
Power OFF and /ON.
Replace Main Motor.
FIP1.5
004 922 No Toner
Time to change drum/toner cartridge
Change drum/toner cartridge
FIP1.16
006 335 ROS Motor fail of rotation
Revolution of ROS Motor doesn’ t become the correct ones for 15sec
and 2sec while Warm Up and Run, respectively.
Defect of ROS Motor(ROS Assy)
Disconnection of wires from MCU PWB J14 to ROS Assy J140 or
loose connection.
FIP1.2
007 313
Option Tray
4cCommunucation Fail
The response of communication with RemoteCPU is error. Check the
connection to Option Tray 4.
FIP1.25
(Separate
volume)
007 950
Tray 1 Paper Size
Mismatch (length slows
scan direction error)
Defect that the length (slows scan direction) of paper fed from Tray 1/
2/3/4 is different form the specified length by measuring with REGI.
Sensor.
Slip of paper feeding roll, wear, fail of rotation
Wear of paper feeding gear, jumping, fail of rotation
Dirt or defect of REGI. Sensor
REGI. Clutch slip, operational falure
FIP1.14
007 951
Tray 2 Paper Size
Mismatch (length slows
scan direction error)
007 952
Tray 3 Paper Size
Mismatch (length slows
scan direction error)
FIP1.23
(Separate
volume)
007 953
Tray 4 Paper Size
Mismatch (length slows
scan direction error)
008 153
Feed Jam 1(Early Feed
Jam)
Paper is fed to Regi too fast.
Check paper set, dirt or defect of REGI. Sensor
FIP1.10
008 155 Regi Sensor On Jam
Regi Sensor is On while Warming up.Scrap of paper is left, dirt or
defect of REGI. Sensor
FIP1.9
008 156 Regi Sensor Off Jam
Paper is not fed from Reg position to Fuser position within the FIP 1.9
specified time. FIP 1.10
Slip of REGI. Roll, wear, fail of rotation
Breakage failure of Fuser drive gear
Dirt or defect of REGI. Sensor
008 176
Tray 1 Regi Sensor On
Jam
Regi Sensor doesn' t become On though the specified time is passed FIP 1.9
after starting Tray1 Feed FIP 1.10
Slip of Tray 1 Feed Roll, wear, fail of rotation
Clutch Assy PH(TRAY1) defects
Dirt or defect of REGI. Sensors
008 180 Dup Miss Feed Jam
Sensor DUP doen' t become ON when Duplex feeding. FIP 1.9
Slip of Feed Roll, wear, fail of rotation FIP 1.10
Dirt or defect of Sensor DUP
008 314
I/F trouble between
HVPS/MCU PWB-DM
Disconnect Duplex Unit after powering on
Check the connection of Duplex Unit and machine
FIP1.27
(Separate
volume)
FIP1.32
(Separate
volume)
009 413 Toner Black 1 Near Empty
Black Toner is almost empty. (No service work)
Change drum/toner cartridge as needed.
009 909
EP Cartridge Type
Missmatch
ID in NVM of IOT machine and ID of drum/toner cartridge are different.
Set the correct drum/toner cartridge.
FIP1.11
009 910 EP Cartridge Not Installed
The drum/toner cartridge is not set.
Set the drum/toner cartridge correctly.
Chain Link Fault Items Conditions of detect/Methods of treatment Ref FIP