Oki B6200 - Page 27

1 - 11
Chapter 1 Troubleshooting
010 105
Fuser Exit Sensor On
Jam
Fuser Exit Sensor doesn’ t detect paper from REGI. Clutch ON after
specific time passed.
Slip of Feed Roll, wear, fail of rotation
Defect of Fuser Exit Sensor
Disconnection of wires from Fuser Exit Sensor J4247-1 to MCU PWB
J11-10 or loose connection
FIP1.7
010 106
Fuser Exit Sensor Off
Jam
Paper doesn’ t go through Fuser Exit Sensor though the specific time
passed after REGI. Sensor go through.
Check whether paper is not rolled to Heat Roll.
Defect of Fuser Exit Sensor
Short out the wires from Fuser Exit Sensor J159-1 to MCU PWB J15-
B3.
FIP1.8
010 112 Exit Out Early Jam
Fuser Exit Sensor becomes OFF in shorter time than specified after
Fuser Exit Sensor detected the top of paper. (Turning to OFF is too
early.)
Check whether paper is not rolled to Fuser Exit Roll.
FIP1.29
(Separate
volume)
010 128
Duplex Pre Regi Sensor
On Jam
Paper comes to Regi from Sensor DUP too fast.
Dirt or defect of Sensor DUP
FIP1.28
(Separate
volume)
010 132
Duplex Path 1 Sensor On
Jam
Paper is not ejected from Sensor DUP within the specific time, or
Sensor DUP is On while Warming up.
Slip of Feed Roll, wear, fail of rotation, scrap of paper is left
Dirt or defect of Sensor DUP
FIP1.29
(Separate
volume)
010 164
Regi.SNR On Jam <Dup
Miss Feed Jam>(not wait)
Paper doesn’ t come to Reg from Sensor DUP within the specific time.
Slip of Feed Roll, wear, fail of rotation
Dirt or defect of Sensor DUP
FIP1.30
(Separate
volume)
010 347
<OCT failure> Offset Fail
(OCT)
Fail to communication with machineCheck the connection to the
machine, and replace PWBA OCT if it is no problem.
FIP1.38
(Separate
volume)
FIP1.42
(Separate
volume)
010 349
Fuser STS Front
Disconnection Fail
Detect Fuser trouble.
Replace Fuser Assy if Power OFF and ON cannot recover the FAIL.
FIP1.3
010 420 Fuser Unit Pre Warning
In the case that PV of Fuser comes to the specified value and the life
time to be end.
Replace Fuser Unit, and Reset HFSI counter.
FIP1.17
011 108
OCT Jam 1 (Paper doesn’
t reach OCT)
Paper doesn’ t come to OCT Sensor from Exit Sensor within the
specific time.
Slip of Feed Roll, wear, fail of rotationDirt or defect of Sensor OCT
FIP1.39
(Separate
volume)
011 109
OCT Jam 2 (Paper is not
ejected form OCT)
Paper is not ejected from OCT Sensor within the specific time, or OCT
Sensor is On while Engine Warming up.
Slip of Feed Roll, wear, fail of rotation
Dirt or defect of Sensor OCT
012 300
Faceup Tray is opened
while printing.
Detect Cover Interlock Open of FaceUpTray in a job,or Standard
mode,or Faceup Tray is opened while printing in OCT mode.
Dirt or defect of Sensor Face Up Open
FIP1.43
(Separate
volume)
012 951 OCT_FULL_STACK
Detect Full Stack(OCT)
Detect paper left in the offset ejecting tray.
Remove paper in IOT Face Down Tray.
Dirt or defect of Sensor Full Stack
FIP1.41
(Separate
volume)
FIP1.44
012 952 FaceUP Tray Open
Detect that Faceup Tray is opened though printing out to Facedown
Tray or OCT is specified.
Dirt or defect of Sensor Face Up Open
FIP1.43
(Separate
volume)
Chain Link Fault Items Conditions of detect/Methods of treatment Ref FIP