Oki B721 Maintenance Manual

Oki Data CONFIDENTIAL
45487001TH Rev.1
4-6 /
4. Maintenance menus
Item Settings Functions
Menus System
Adjust
Timeout Network 0 seconds
5 seconds
~
90 seconds
~
290 seconds
295 seconds
300 seconds
Time of open of Network port after end of
job
Time of the port open indicates the time
that open the current port which receiving
the current job and so other port be able
to receive data.
It increase /decreases in the step of 5
[Conditions for display]
A NIC FW is installed.
Low Toner
Continue
Stop
Sets printer operation when Toner Low is
detected.
In CONTINUE, the printer can continue
printing while remaining ON-LINE.
In STOP, it becomes OFF-LINE.
[Conditions for display]
The consumable is SEPARATION mode or
COMBINATION mode will be decided by
a PU Factory PJL command. This menu
item is only displayed in the SEPARATION
mode.
Jam Recovery
On
Off
Sets whether JAM RECOVERY printing is
performed or not when Jam occurs.
When it is set to OFF, a job that includes
the page to which Jam has occurred will
be cancelled.
Error Report
On
Off
Sets whether an error report is printed or
not when an internal error occurs.
Valid only for PS and PCL XL.
Hex Dump Execute Prints out data received from the host
PC in the hexadecimal Dump. Turning off
the power supply switch restores Normal
Mode from HEX Dump Mode.
Item Settings Functions
Menus Print
Adjust
Print
Position
Adjust
MPtray,
Tray1,
Tray2,
Tray3,
Tr ay 4
X
Adjust
0.00 mm
+0.25 mm to
+2.00 mm
-2.00 mm to
-0.25 mm
Adjusts the position of a whole print image
in the direction that is perpendicular to the
direction paper runs, that is horizontally (at
0.25 mm pitch).
Y
Adjust
0.00 mm
+0.25 mm to
+2.00 mm
-2.00 mm to
-0.25 mm
Adjust the position of a whole print image
in the direction paper runs, that is vertically
(at 0.25mm pitch).
Duplex
print X
Adjust
0.00 mm
+0.25 mm to
+2.00 mm
-2.00 mm to
-0.25 mm
At the time of back page printing of
Duplex, adjusts the position of the
whole print image in the direction that is
perpendicular to the direction paper runs,
that is horizontally (at 0.25mm pitch).
Duplex
print Y
Adjust
0.00 mm
+0.25 mm to
+2.00 mm
-2.00 mm to
-0.25 mm
At the time of back page printing of
Duplex, adjusts the position of a whole
print image in the direction paper runs,
that is vertically (at 0.25mm pitch).
Paper Black Setting
0
+1
+2
+3
-3
-2
-1
Use it for fine adjustment of the significant
dust attachment on the surface and when
thin spot has the sighificant impact on the
standard/BLACK printing or other cases
occur. The decrement is necessary if the
scattered or snow-white like printing is the
result in the high density-printing area. The
increment is necessary if the thin printing
is found.
Trans. Black Setting
0
+1
+2
+3
-3
-2
-1
Use it for fine adjustment of the significant
dust attachment on the surface and when
thin spot has the significant impact on
OHP/BLACK printing. The decrement
is necessary if the scattered or snow-
white like printing is the result in the high
density-printing area. The increment is
necessary if the thin printing is found.

Oki B721 Specifications

General

Print Technology	LED
Resolution	1200 x 1200 dpi
Processor	533 MHz
Memory	256 MB
Connectivity	USB, Ethernet
Duplex Printing	Standard