Name: Planet MGSW-24160F
Brand: Planet
Rating: 4 (1 reviews)

To Next Page

To Previous Page

User’s Manual of MGSW-24160F

1. It recommends using PLANET SFPs on the Managed Switch. If you insert a SFP transceiver that

is not supported, the Managed Switch will not recognize it.

2. MGB series SFP modules are guaranteed working under -10 ~ 50℃ environmet, but MGB-TSX /

MGB-TLX / MBG-T30 / MGB-T70 supports to -40 ~ 75℃.

3. MFB series SFP modules are guaranteed working under -10 ~ 50℃ environmet, but MFB-TFX /

MFB-TF20 supports to -40 ~ 75℃.

Before connect the other Managed Switches, workstation or Media Converter.

1. Make sure both side of the SFP transceiver are with the same media type, for example: 1000Base-SX to 1000Base-SX,

1000Bas-LX to 1000Base-LX.

2. Check the fiber-optic cable type match the SFP transceiver model.

 To connect to 1000Base-SX SFP transceiver, use the Multi-mode fiber cable- with one side must be male duplex LC

connector type.

 To connect to 1000Base-LX SFP transceiver, use the Single-mode fiber cable-with one side must be male duplex LC

connector type.

 Connect the fiber cable

1. Attach the duplex LC connector on the network cable into the SFP transceiver.

2. Connect the other end of the cable to a device – switches with SFP installed, fiber NIC on a workstation or a Media

Converter..

3. Check the LNK/ACT LED of the SFP slot on the front of the Managed Switch. Ensure that the SFP transceiver is operating

correctly.

4. Check the Link mode of the SFP port if the link failed. Co works with some fiber-NICs or Media Converters, set the Link

mode to “1000 Force” is needed.

 Remove the transceiver module

1. Make sure there is no network activity by consult or check with the network administrator. Or through the management

interface of the switch/converter (if available) to disable the port in advance.

2. Remove the Fiber Optic Cable gently.

3. Turn the handle of the MGB module to horizontal.

4. Pull out the module gently through the handle.

Planet MGSW-24160F Specifications

General

Console port	RS-232
Compatible memory cards	Not supported
SFP module slots quantity	16
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
10G support	No
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Private VLAN, Protocol-based VLAN, Port-based VLAN
Copper ethernet cabling technology	10BASE-T, 100BASE-FX, 100BASE-TX, 100BASE-T, 1000BASE-T, 1000BASE-TX
MAC address auto-learning supported	Yes
Throughput	35.6 Mpps
Jumbo frames	10000
MAC address table	16000 entries
Form factor	1U
Product color	Blue
Number of fans	2 fan(s)
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	38 W
Number of multicast groups filtered	255
Switch type	Managed
Switch layer	L2+
DHCP features	DHCP server, DHCP client
Security algorithms	SNMP, SSH, SSL/TLS
Storage temperature (T-T)	-10 - 70 °C
Operating temperature (T-T)	0 - 60 °C
Operating relative humidity (H-H)	5 - 95 %
Transmission distance (max)	120 km
Fiber ethernet cabling technology	1000BASE-X
Harmonized System (HS) code	85176990