Need help?Do you have a question about the ProSoft PLX32-EIP-MBTCP-UA and is the answer not in the manual?
Provides channels for user feedback and contact details for ProSoft Technology.
Outlines the disclaimer and copyright information for the manual's content.
Details critical installation instructions and safety warnings, including explosion hazards.
Lists the various agency approvals and certifications obtained by the product.
Explains the features and purpose of the PLX32-EIP-MBTCP-UA gateway and its configuration software.
Lists the minimum system components required for the ProSoft Configuration Builder software.
Details the components included with the PLX32-EIP-MBTCP-UA for installation and configuration.
Provides step-by-step instructions for mounting the gateway onto a DIN-rail.
Explains the function of the three pairs of jumper pins located on the back of the gateway.
Describes the use and functionality of an optional SD card for the gateway.
Details how to safely connect power to the gateway unit, including a warning about polarity.
Guides on downloading and installing the ProSoft Configuration Builder software.
Explains how to establish an Ethernet connection between a PC and the gateway.
Details the process of setting a temporary IP address for the gateway using ProSoft Discovery Service.
Guides on how to set up a new project in ProSoft Configuration Builder, including adding the gateway.
Explains how to disable specific driver functionalities on the gateway if they are not needed.
Describes how to configure various gateway parameters within the ProSoft Configuration Builder software.
Explains how to rename objects like folders and modules within the ProSoft Configuration Builder project.
Details the steps to print the current configuration file from ProSoft Configuration Builder.
Guides on setting the Ethernet port parameters (IP address, Netmask, Gateway) for the gateway.
Explains how to map data between different areas in the gateway's internal database for simpler data requests.
Specifies the starting internal database register address for the copy operation in data mapping.
Specifies the beginning destination register address for the copy operation in data mapping.
Specifies the number of registers to be copied during a data mapping operation.
Allows rearranging byte or word order during data copying for protocol compatibility.
Sets an interval between data map copy operations to manage firmware scan cycles.
Explains how to copy the configured project file from the PC to the gateway.
Details how to copy project settings from the gateway back to the PC.
Explains how to use the gateway's LED indicators to diagnose problems and understand the unit's status.
Describes the function and states of the main gateway front panel LEDs for troubleshooting.
Details the status indicated by the Ethernet port LEDs on the gateway.
Guides on using ProSoft Configuration Builder's diagnostic tools to retrieve status, configuration, and other data.
Explains the tree structure of the Diagnostics menu and its commands for system testing and debugging.
Details how to capture diagnostic session data into a log file for troubleshooting or support.
Explains how to perform a warm or cold boot on the gateway through the software.
Describes where and how the gateway stores status data in its internal database.
Lists the contents and register addresses for the gateway's general status data.
Indicates that protocol-specific status data is also stored in upper memory locations.
Lists the technical specifications of the gateway's hardware, including power, dimensions, and ports.
Provides an overview of the EtherNet/IP protocol's functionality with the gateway.
Details the general specifications for EtherNet/IP connections supported by the gateway driver.
Explains the structure and purpose of the gateway's internal database for EIP protocol operations.
Guides on configuring EtherNet/IP specific settings for the gateway.
Details how to configure the gateway as an EtherNet/IP Class 3 Server for message responses.
Guides on setting up an EtherNet/IP Class 1 connection for direct I/O data transfer with a PLC.
Explains how to configure EIP Class 3 Client and UClient connections for master/client messaging.
Describes how to use ProSoft Configuration Builder for diagnostics related to the EIP driver.
Summarizes the status information available in PCB for troubleshooting the EIP driver.
Details the EIP driver's status data addresses in upper memory for connected and unconnected clients.
Lists and explains various EtherNet/IP error codes encountered during operations.
Provides reference information for EIP protocol, including specifics for SLC and MicroLogix processors.
Offers specific guidance for using EIP with SLC and MicroLogix processors, including messaging examples.
Provides reference information for using EIP with PLC5 processors, including messaging examples.
Explains how to use EIP with ControlLogix and CompactLogix processors, covering PCCC and CIP messages.
Introduces the Modbus TCP/IP (MBTCP) protocol and its capabilities with the gateway.
Lists the general specifications for Modbus TCP/IP connections supported by the gateway.
Explains the structure of the MBTCP internal database and how data is stored.
Guides on configuring MBTCP settings for the gateway.
Details how to configure MBTCP server parameters, including offsets and float settings.
Guides on setting up MBTCP client parameters and command lists for gateway emulation.
Explains how to define Modbus TCP/IP commands for the MBTCP client.
Describes how to use ProSoft Configuration Builder for diagnostics related to the MBTCP driver.
Summarizes status information available in PCB for troubleshooting the MBTCP driver.
Details MBTCP driver status data addresses in upper memory for servers and clients.
Lists and explains standard Modbus, MBTCP client, and communication error codes.
Provides reference information about the Modbus protocol and supported function codes.
Explains the history and functionality of the Modbus protocol and Modbus TCP/IP.
Introduces the PSW-UACM software used for configuring the OPC UA Server.
Guides on downloading and installing the UA Server Configuration Manager software.
Explains how to synchronize the gateway's system time with an NTP server.
Details how to launch the UA Server Configuration Manager software.
Guides through the process of generating and managing certificates for OPC UA security.
Explains how to modify endpoint configuration for implementing security policies.
Guides on creating a provisioning certificate for initial device connections.
Details the process of creating a Certificate Authority (CA) certificate to sign device certificates.
Guides on creating an application instance certificate for connections to provisioned devices.
Explains how to connect to a device and refresh its status in the PSW-UACM software.
Guides on creating and signing a new device certificate for secured communication.
Details how to import an OPC UA Client's certificate public key file into the PSW-UACM trust list.
Guides on exporting the CA certificate for use by an OPC UA client.
Explains the purpose and management of the Certificate Revocation List.
Guides on downloading the trust list configuration to the gateway.
Explains how to configure user permissions and access control for the OPC UA Server.
Details the process of adding a new user account within the PSW-UACM.
Guides on assigning users to groups to manage their permissions and access levels.
Explains how to create and map tags for accessing gateway data through the OPC UA Server.
Covers the advanced operational parameters and adjustable values for the OPC UA Server.
Details how to save the configured settings for the OPC UA Server.
Guides on establishing UA client connectivity to the gateway's UA Server.
Provides an example of mapping live data from the gateway to the UA Client.
Covers the general setup for a UA Client to communicate with the UA Server.
Provides guidance on troubleshooting and maintaining the OPC UA Server.
Explains how to interpret the Status tab for device state and variable load results.
Guides on viewing and exporting communication error logs for troubleshooting.
Explains how to use PCB diagnostics for OPC UA Server configuration and status.
Details how to reset the OPC UA Server to its default state.
Describes how to back up the PSW-UACM configuration database.
Guides on migrating the PSW-UACM installation to another computer.
Provides information on what details to gather before contacting technical support for assistance.
Directs users to ProSoft Technology's website for complete warranty, support, and service details.
Provides channels for user feedback and contact details for ProSoft Technology.
Outlines the disclaimer and copyright information for the manual's content.
Details critical installation instructions and safety warnings, including explosion hazards.
Lists the various agency approvals and certifications obtained by the product.
Explains the features and purpose of the PLX32-EIP-MBTCP-UA gateway and its configuration software.
Lists the minimum system components required for the ProSoft Configuration Builder software.
Details the components included with the PLX32-EIP-MBTCP-UA for installation and configuration.
Provides step-by-step instructions for mounting the gateway onto a DIN-rail.
Explains the function of the three pairs of jumper pins located on the back of the gateway.
Describes the use and functionality of an optional SD card for the gateway.
Details how to safely connect power to the gateway unit, including a warning about polarity.
Guides on downloading and installing the ProSoft Configuration Builder software.
Explains how to establish an Ethernet connection between a PC and the gateway.
Details the process of setting a temporary IP address for the gateway using ProSoft Discovery Service.
Guides on how to set up a new project in ProSoft Configuration Builder, including adding the gateway.
Explains how to disable specific driver functionalities on the gateway if they are not needed.
Describes how to configure various gateway parameters within the ProSoft Configuration Builder software.
Explains how to rename objects like folders and modules within the ProSoft Configuration Builder project.
Details the steps to print the current configuration file from ProSoft Configuration Builder.
Guides on setting the Ethernet port parameters (IP address, Netmask, Gateway) for the gateway.
Explains how to map data between different areas in the gateway's internal database for simpler data requests.
Specifies the starting internal database register address for the copy operation in data mapping.
Specifies the beginning destination register address for the copy operation in data mapping.
Specifies the number of registers to be copied during a data mapping operation.
Allows rearranging byte or word order during data copying for protocol compatibility.
Sets an interval between data map copy operations to manage firmware scan cycles.
Explains how to copy the configured project file from the PC to the gateway.
Details how to copy project settings from the gateway back to the PC.
Explains how to use the gateway's LED indicators to diagnose problems and understand the unit's status.
Describes the function and states of the main gateway front panel LEDs for troubleshooting.
Details the status indicated by the Ethernet port LEDs on the gateway.
Guides on using ProSoft Configuration Builder's diagnostic tools to retrieve status, configuration, and other data.
Explains the tree structure of the Diagnostics menu and its commands for system testing and debugging.
Details how to capture diagnostic session data into a log file for troubleshooting or support.
Explains how to perform a warm or cold boot on the gateway through the software.
Describes where and how the gateway stores status data in its internal database.
Lists the contents and register addresses for the gateway's general status data.
Indicates that protocol-specific status data is also stored in upper memory locations.
Lists the technical specifications of the gateway's hardware, including power, dimensions, and ports.
Provides an overview of the EtherNet/IP protocol's functionality with the gateway.
Details the general specifications for EtherNet/IP connections supported by the gateway driver.
Explains the structure and purpose of the gateway's internal database for EIP protocol operations.
Guides on configuring EtherNet/IP specific settings for the gateway.
Details how to configure the gateway as an EtherNet/IP Class 3 Server for message responses.
Guides on setting up an EtherNet/IP Class 1 connection for direct I/O data transfer with a PLC.
Explains how to configure EIP Class 3 Client and UClient connections for master/client messaging.
Describes how to use ProSoft Configuration Builder for diagnostics related to the EIP driver.
Summarizes the status information available in PCB for troubleshooting the EIP driver.
Details the EIP driver's status data addresses in upper memory for connected and unconnected clients.
Lists and explains various EtherNet/IP error codes encountered during operations.
Provides reference information for EIP protocol, including specifics for SLC and MicroLogix processors.
Offers specific guidance for using EIP with SLC and MicroLogix processors, including messaging examples.
Provides reference information for using EIP with PLC5 processors, including messaging examples.
Explains how to use EIP with ControlLogix and CompactLogix processors, covering PCCC and CIP messages.
Introduces the Modbus TCP/IP (MBTCP) protocol and its capabilities with the gateway.
Lists the general specifications for Modbus TCP/IP connections supported by the gateway.
Explains the structure of the MBTCP internal database and how data is stored.
Guides on configuring MBTCP settings for the gateway.
Details how to configure MBTCP server parameters, including offsets and float settings.
Guides on setting up MBTCP client parameters and command lists for gateway emulation.
Explains how to define Modbus TCP/IP commands for the MBTCP client.
Describes how to use ProSoft Configuration Builder for diagnostics related to the MBTCP driver.
Summarizes status information available in PCB for troubleshooting the MBTCP driver.
Details MBTCP driver status data addresses in upper memory for servers and clients.
Lists and explains standard Modbus, MBTCP client, and communication error codes.
Provides reference information about the Modbus protocol and supported function codes.
Explains the history and functionality of the Modbus protocol and Modbus TCP/IP.
Introduces the PSW-UACM software used for configuring the OPC UA Server.
Guides on downloading and installing the UA Server Configuration Manager software.
Explains how to synchronize the gateway's system time with an NTP server.
Details how to launch the UA Server Configuration Manager software.
Guides through the process of generating and managing certificates for OPC UA security.
Explains how to modify endpoint configuration for implementing security policies.
Guides on creating a provisioning certificate for initial device connections.
Details the process of creating a Certificate Authority (CA) certificate to sign device certificates.
Guides on creating an application instance certificate for connections to provisioned devices.
Explains how to connect to a device and refresh its status in the PSW-UACM software.
Guides on creating and signing a new device certificate for secured communication.
Details how to import an OPC UA Client's certificate public key file into the PSW-UACM trust list.
Guides on exporting the CA certificate for use by an OPC UA client.
Explains the purpose and management of the Certificate Revocation List.
Guides on downloading the trust list configuration to the gateway.
Explains how to configure user permissions and access control for the OPC UA Server.
Details the process of adding a new user account within the PSW-UACM.
Guides on assigning users to groups to manage their permissions and access levels.
Explains how to create and map tags for accessing gateway data through the OPC UA Server.
Covers the advanced operational parameters and adjustable values for the OPC UA Server.
Details how to save the configured settings for the OPC UA Server.
Guides on establishing UA client connectivity to the gateway's UA Server.
Provides an example of mapping live data from the gateway to the UA Client.
Covers the general setup for a UA Client to communicate with the UA Server.
Provides guidance on troubleshooting and maintaining the OPC UA Server.
Explains how to interpret the Status tab for device state and variable load results.
Guides on viewing and exporting communication error logs for troubleshooting.
Explains how to use PCB diagnostics for OPC UA Server configuration and status.
Details how to reset the OPC UA Server to its default state.
Describes how to back up the PSW-UACM configuration database.
Guides on migrating the PSW-UACM installation to another computer.
Provides information on what details to gather before contacting technical support for assistance.
Directs users to ProSoft Technology's website for complete warranty, support, and service details.
To Next Page
General