Siemens 6RA7086-6KS22

Function diagrams 05.05
8-42 SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Sheet G170 USS interface 1
.04 .01 .03 .02 .06 .05 .07 .08 .10 .09 .14 .11 .13 .12 .16 .15
Rx+/Tx+ Rx-/Tx-
RS485
M
1
1
RS232
1
≥
2 3 4 5 6 7 8 9
TxD RxD
1
M
+5V
Submin D
M
+
1
0
1
0
87564321
- G170 -
015
.01 .16
PMU
<1>
<1>
[G169.2]
[G182.6] [G151.3] [G183.6]
K K K K
P784
K K K K K K
K2001 K2002 K2003 K2004 K2005 K2006 K2007 K2008 K2009 K2010 K2011 K2012 K2013 K2014 K2015 K2016
B2100
Bit 0 ... Bit 15
B2200 B2300 B2400 B2500 B2600 B2700 B2800 B2900
K K K K K K
r810.17 r810.18 r810.19 r810.20
r811.17 r811.18 r811.19 r811.20
B2115 B2215 B2315 B2415 B2515 B2615 B2715 B2815 B2915
P780 (2) P787 (0,000s) P786 (0)
P783 (6)
P781 (2) P782 (127)
r789
P927
1s
B2030 B2031
P788 (2030)
B
X300: G-SST1
P785.001 (0)
32
167
0
33
0 0 0 0 0 0 0 0 0 0 0 0
U116 (0)
B B
K2020
r810.01 to .16
r811.01 to .16
USS interface 1
Word 1
Word 2 Word 3 Word 4 Word 5 Word 6 Word 7 Word 8
Word 9
Word 10
Process data
from USS interface
Word 1 Word 2 Word 3 Word 4 Word 5 Word 6 Word 7 Word 8 Word 9
Word 10
Process Data
to USS interface
Receive data
Transmit data
Word 11
Word 12 Word 13 Word 14 Word 15 Word 16
every 16 bits
Word 11
Word 12 Word 13 Word 14 Word 15 Word 16
Word 1: Param.-ID (PKE) Word 2: Param.Index Word 3: Param.Value Low Word Word 4: Param.Value High Word
Parameter
processing
Word 1: Param.-ID (PKE) Word 2: Param.Index Word 3: Param.Value Low Word Word 4: Param.Value High Word
USS parameter data
USS parameter data
Bus terminator
1 = "Fault F011"
Fault message trigger
USS On/Off
Slave address
Baud rate Length of process data Length of parameter data Telegram monitoring time USS diagnostic parameter Enable parameterization
1 = "Telegram monitoring timeout"
Parameters for USS interface
FS
Binector / connector
converter
P785.002=0: Bit 10 is
not treated as "control by PLC".
P785.002=1: Bit 10 is treated as "control by PLC", i.e. when bit 10=0, the other bits of word 1 as well as words 2 to 16 are
not written to connectors K2001 to K2016
or to binectors B2100 to 2915. All these connectors and binectors retain their old values.
For transmission of double-word connectors see Section 9.13.1 See also connector type converter on sheet G169