Siemens 6RA7086-6KS22

Function diagrams 05.05
8-44 SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Sheet G172 USS interface 3
.04 .01 .03 .02 .06 .05 .07 .08 .10 .09 .14 .11 .13 .12 .16 .15
61 62 63 64 65
1
Tx+ Tx- Rx+/Tx+ Rx-/Tx-
M
RS485
1
M
+
10 10
87564321
- G172 -
X162
015
.01 .16
CUD2
<1>
<1>
[G169.6]
[G182.6] [G151.3] [G183.6]
Bit 0 ... Bit 15
r814.17 r814.18 r814.19 r814.20 r815.17 r815.18 r815.19 r815.20
G-SST3
K9001 K9002 K9003 K9004 K9005 K9006 K9007 K9008 K9009 K9010 K9011 K9012 K9013 K9014 K9015 K9016
B9100 B9200 B9300 B9400 B9500 B9600 B9700 B9800 B9900
B9215 B9315 B9415 B9515 B9615 B9715 B9815 B9915
P800 (0) P807 (0,000s) P806 (0) P803 (13) P801 (2) P802 (127)
r809
P927
1s
B9030 B9031
P808 (9030)
B
P805.001 (0)
B9115
K K K K
P804
K K K K K K K K K K K K
32
167
0
33
0 0
0
0 0 0 0 0 0 0
0 0
U118 (0)
B B
K9020
Binector / connector
converter
USS interface 3
Word 1
Word 2 Word 3 Word 4 Word 5 Word 6 Word 7 Word 8
Word 9
Word 10
Process data
from USS interface
r815.01 to .16
Word 1 Word 2 Word 3 Word 4 Word 5 Word 6 Word 7 Word 8 Word 9
Word 10
Process data
to USS interface
Receive data
Transmit data
Word 11
Word 12 Word 13 Word 14 Word 15 Word 16
Word 11
Word 12 Word 13 Word 14 Word 15 Word 16
Word 1: Param.-ID (PKE) Word 2: Param.Index Word 3: Param.Value Low Word Word 4: Param.Value High Word
Parameter
processing
Word 1: Param.-ID (PKE) Word 2: Param.Index Word 3: Param.Value Low Word Word 4: Param.Value High Word
USS parameter data
Bus terminator
1 = "Fault F013"
Fault message trigger
USS On/Off
Slave address
Baud rate Length of process data Length of parameter data
Parameters for USS interface
Telegram monitoring time USS diagnostic parameter Enable parameterization
1 = "Telegram monitoring timeout"
r814.01 to .16
every 16 bits
USS parameter data
FS
P805.002=0: Bit 10 is
not treated as "control by PLC".
P805.002=1: Bit 10 is treated as "control by PLC", i.e. when bit 10=0, the other bits of word 1 as well as words 2 to 16 are
not written to connectors K9001 to K9016
or to binectors B9100 to 9915. All these connectors and binectors retain their old values.
For transmission of double-word connectors see Section 9.13.1 See also connector type converter on sheet G169