Siemens 6RA7086-6KS22

05.05 Function diagrams
SIEMENS AG 6RX1700-0AD76 8-57
SIMOREG DC Master Operating Instructions
Sheet G195 Paralleling interface
.01 .02
.03
.04 .05
1
1
87564321
- G195 -
1 0
2
Rx+/Tx+ Rx-/Tx- Rx+/Tx+ Rx-/Tx- Rx+/Tx+ Rx-/Tx- Rx+/Tx+ Rx-/Tx-
0 1 0 1 0 1 0
1
2..6
12..16
1
≥
X165
X166
3210
4
5
6
1
≥
&
CUD2
[G195.6] [G195.6] [G195.6] [G195.6] [G195.6]
7
89
15
.07
.08
.09 .10 .06
[G195.6] [G195.6] [G195.6] [G195.6] [G195.6]
U800 (0) U807 (0,100s) U806 (2) n809
n813.01 ... .05
K6021 K6025 K6024 K6023 K6022
U804 (0)
K K K K K
U808(6040)
B
1s
B6041
Bit 0 ... Bit 15
B6220
B6235
K6031 K6035 K6034 K6033 K6032
Bit 0 ... Bit 15
B6320
B6335
16Bit
K6041 K6045 K6044 K6043
K6042
Bit 0 ... Bit 15
B6420
B6435
16Bit
K6051 K6055 K6054 K6053 K6052
Bit 0 ... Bit 15
B6520
B6535
16Bit
K6061
K6065
K6064 K6063 K6062
Bit 0 ... Bit 15
B6620
B6635
16Bit
U800 (0)
B6040
U805 (0)
U806 (2)
RS485 RS485 RS485 RS485
Imp.,
α
n810
n810:
B6223 B6323 B6423 B6523 B6623
1
→
F044
16Bit
U803 (0)
B0225
K K K K K
B6222 B6322 B6422 B6522 B6622
Receiving data
Transmit data
On/Off
Telegram monitoring time Diagnostic parameter
to next
drive
Fault signal trip
1 = "Telegram monitoring timeout"
Word 1 Word 2 Word 3
Word 4
Word 5
Bus terminator
1 = "Fault F014"
Paralleling interface
from master
from slave 3 from slave 4 from slave 5 from slave 6
Torque direction,
thyristor
selection
Firing pulse
Internal firing pulse
Summation firing pulse
Parameters for paralleling interface:
Bus adress
Internal summation firing pulse
from Slave 2 from master
CLK from Master CLK to slaves
Display active slaves (see right)
Master (12...16) /
Slave (2...6)
Word 1 Word 2 Word 3 Word 4 Word 5
Word 1 Word 2 Word 3 Word 4 Word 5
Word 1 Word 2 Word 3 Word 4 Word 5 Word 1 Word 2 Word 3 Word 4 Word 5
Word 1
Word 2 Word 3 Word 4 Word 5
n812.01 to .05 n812.06 to .10 n812.11 to .15 n812.16 to .20 n812.21 to .25
Word1 bit2 = Run
bit3 = Fault
U800 <> 0
Operating state <o1.0
U806 >10
Operating mode for parallel connection
Paralleling master: (i.e. when U800 = 1) Segment 2 ... ON: Slave with address 2 responding 3 ... ON: Slave with address 3 responding 4 ... ON: Slave with address 4 responding 5 ... ON: Slave with address 5 responding 6 ... ON: Slave with address 6 responding 8, 9 ... OFF 15.. ON: Master function active Paralleling slave: (i.e. when U800 = 2):
Segment 2 ... ON: Data for slave with address 2 are ok 3 ... ON: Data for slave with address 3 are ok 4 ... ON: Data for slave with address 4 are ok 5 ... ON: Data for slave with address 5 are ok 6 ... ON: Data for slave with address 6 are ok 8 ... ON: Slave funktion active 9 ... ON: Firing pulses of master are used 15.. OFF
1 = active paralleling master
Indices .06 to .10 of U804 are activated on the master and the standby master when the “master” function is transferred to the standby master