Index
NC/PLC Interface Signals (Z1)
Index-4 Function Manual, 08/2005 Edition, 6FC5397-0BP10-0BA0
I
Interface signals
611D Ready, 2-4
Acknowledge EMERGENCY STOP, 2-113
Acknowledge fixed stop reached, 2-71
Action block active, 2-97
Activate associated M1, 2-74
Activate channel-specific protection zone, 2-65
Activate dry run feed, 2-133
Activate fixed feed rate 1 - 4 for machine axes,
2-143
Activate fixed feed rate 1 - 4 for path/geometry
axes, 2-141
Activate M01, 2-91
Activate program test, 2-92
Activate referencing, 2-115
Activate single block, 2-90
Activate travel to fixed stop, 2-73
Active, 2-22
Active drive parameter set A, B, C, 2-48
Active G function of groups 1 to 60, 2-105
Active JOG mode, 2-88
Active machine function REF, 2-90
Active machine function TEACH IN, 2-89
Active mode AUTOMATIC, 2-87
Active mode MDA, 2-88
Active motor A, B, 2-49
Active or passive file system, 2-15, 2-16
Active REPOS machine function, 2-89
Active spindle control mode, 2-130
Active spindle mode oscillation mode, 2-131
Active spindle positioning mode, 2-131
Actual direction of rotation clockwise, 2-128
Actual gear stage A to C, 2-121
Actual value in WCS, 2-9
Air temperature alarm, 2-6
Alarm area selection, 2-11
All axes stationary, 2-69
All axes that have to be referenced are
referenced, 2-116
All channels in the reset state, 2-89
Analog spindle 1, utilization in percent, 2-10
Analog spindle 2, utilization in percent, 2-10
Associated M01/M00 active, 2-79
ASUB is stopped, 2-105
AT box ready, 2-2
AUTOMATIC mode, 2-80
Axis/spindle disable, 2-27
Axis/spindle stops, 2-43
Block search active, 2-98
Block search via program test is active, 2-106
Cancel alarm cleared, 2-17
Change gear stage, 2-127
Channel number (FC9: ChanNo), 2-24
Channel number of the machine control panel on
the MMC, 2-10
Channel status active, 2-103
Channel status interrupted, 2-103
Channel status reset, 2-103
Channel-specific NCK alarm is active, 2-25
Channel-specific protection zone preactivated, 2-65
Channel-specific protection zone violated, 2-66
Clamping in progress, 2-67
Clear cancel alarms, 2-9
Clear recall alarms, 2-9
COM1, 2-12, 2-20
COM2, 2-11, 2-19
Controller enable, 2-33
Controller parameter set switchover (checkback
signal), 2-45
Controller parameter set switchover (request), 2-35
Current controller active, 2-45
D function 1, 2-77
Darken screen, 2-8
Data transfer error, 2-24
Delete distance-to-go (axis-specific)/Spindle
reset, 2-34
Delete distance-to-go (channel-specific), 2-25
Delete S value, 2-119
Disable parameter set switchover commands from
NC, 2-36
Displayed channel number from the MMC, 2-19
Drive parameter set selection A, B, C, 2-38
Drive Ready, 2-49
Drive test travel enable, 2-41
Drive test travel request, 2-42
Dry run feed rate selected, 2-140
EMERGENCY STOP, 2-113
EMERGENCY STOP active, 2-114
Enable travel to fixed stop, 2-72
Encoder limit frequency exceeded, 2-69
Error, 2-19, 2-22
Error RS-232-C, 2-21
Extended address F functions 1 to 6, 2-78
Extended address H functions 1 to 3, 2-77
Extended address M functions 1 to 5, 2-75
Extended address S functions 1 to 3, 2-76
External zero offset, 2-112
F function for positioning axis, 2-147
FC9 Out: Active, 2-16
FC9 Out: Done, 2-16
FC9 Out: Error, 2-17
FC9 Out: StartError, 2-17
FC9: Start (measuring in Jog mode), 2-24
Feed disable, 2-138
Feed rate override, 2-134
Feed rate override (axis-specific), 2-141
To Next Page
Loading...
