TELEDYNE API T300M - Page 13

083730300A DCN8101 xi
FIGURES
Figure 2-1. Front Panel Layout .................................................................................................................................20
Figure 2-2. Rear Panel Layout .................................................................................................................................21
Figure 2-3. Internal Layout – T300 ...........................................................................................................................23
Figure 2-4. Internal Layout – T300M ........................................................................................................................24
Figure 2-5. Optical Bench Layout (shorter bench, T300M, shown) ..........................................................................25
Figure 2-6. Analog Output Connector ......................................................................................................................27
Figure 2-7. Current Loop Option Installed on Motherboard .....................................................................................28
Figure 2-8. Status Output Connector for Digital Outputs..........................................................................................29
Figure 2-9. Control Input Connector .........................................................................................................................30
Figure 2-10. Concentration Alarm Relay ..................................................................................................................31
Figure 2-11. Rear Panel Connector Pin-Outs for RS-232 Mode ..............................................................................32
Figure 2-12. Default Pin Assignments for CPU COM Port connector (RS-232) ......................................................33
Figure 2-13. Jumper and Cables for Multidrop Mode ...............................................................................................35
Figure 2-14. RS-232-Multidrop PCA Host/Analyzer Interconnect Diagram .............................................................36
Figure 2-15. T300/T300M Pneumatic Connections – Basic Configuration Using Bottled Span Gas ......................40
Figure 2-16. T300/T300M Pneumatic Connections – Basic Configuration Using Gas Dilution Calibrator ..............41
Figure 2-17. T300/T300M Pneumatic Connections – Option 50A: Zero/Span ........................................................42
Figure 2-18. T300/T300M Pneumatic Connections – Option 50B: Ambient Zero/Pressurized Span ......................44
Figure 2-19. T300/T300M Pneumatic Connections – Option 50E: Zero Scrubber/Pressurized Span .....................45
Figure 2-20. T300 Pneumatic Connections – Option 50H: Zero/Span.....................................................................47
Figure 2-21. T300/T300M Internal Gas Flow (Basic Configuration) .........................................................................48
Figure 2-22. T300/T300M Internal Pneumatic Flow Option 50A – Zero/Span Valves .............................................49
Figure 2-23. T300/T300M Internal Pneumatic Flow Option 50B – Zero/Span/Shutoff Valves.................................50
Figure 2-24. T300/T300M Internal Pneumatic Flow Option 50E – Zero Scrubber/Pressurized Span with IZS .......51
Figure 2-25. T300 Internal Pneumatic Flow Option 50H – Zero Scrubber/Ambient Span .......................................52
Figure 2-26. T300/T300M Internal Pneumatics with O
2
Sensor Option ...................................................................53
Figure 2-27. T300/T300M Internal Pneumatics with CO
2
Sensor Option ................................................................53
Figure 2-28. Status Screens at Startup ....................................................................................................................54
Figure 2-29. Home Page Example ...........................................................................................................................55
Figure 2-30. Viewing Active Alerts Page ..................................................................................................................55
Figure 2-31. Sample Dashboard Page .....................................................................................................................56
Figure 2-43. DAS Download Page ...........................................................................................................................67
Figure 2-49. Homescreen Configuration ..................................................................................................................73
Figure 2-50. Digital Outputs Setup ...........................................................................................................................74
Figure 2-51. Analog Output Configuration Example .................................................................................................75
Figure 2-52. Analog Outputs Group Calibration Screen...........................................................................................76
Figure 2-53. Analog Outputs Manual Calibration Screen (AOUT2 Example) ..........................................................76
Figure 2-54. Setup for Checking / Calibrating DCV Analog Output Signal Levels ...................................................77
Figure 2-55. Setup for Checking / Calibration Current Output Signal Levels ...........................................................78
Figure 2-56. Alternative Setup Using 250Ω Resistor for Checking Current Output Signal Levels ...........................79
Figure 2-57. Communications Configuration, Network Settings ..............................................................................81
Figure 2-58. Configuration Transfer .........................................................................................................................82
Figure 3-1. MODBUS via Ethernet ...........................................................................................................................85
Figure 3-2. MODBUS via Serial Communication (example) ....................................................................................86
Figure 3-3. Serial Communication, Setting Hessen Protocol ...................................................................................87
Figure 4-1. Multi-Point Calibration Page ..................................................................................................................93
Figure 4-2. Zero and Span Calibration Screens .......................................................................................................95
Figure 4-3. Auto Cal Page ........................................................................................................................................97
Figure 4-4. O
2
Sensor Calibration Set Up ..............................................................................................................100