Unipulse f395 - Slope Detection Interval a; Slope Detection Interval B

To Next Page

To Previous Page

16.Code Setting

125

16-3-6. Slope Detection Interval A

Displays the relationship to the present value of Minimum Slope Detection Value / Slope

Detection Interval B.

16-3-7. Slope Detection Interval B

Displays the relationship to the present value of Minimum Slope Detection Value / Slope

Detection Interval A.

Reference line (blue)

Green

Red

Green

Red

Slope Detection

Interval A

Changes with the

present value of

Slope Detection

Interval B (light blue)

Green

Red

Reference line (blue)

Changes with the

present value of

Slope Detection

Interval A (light blue)

Slope Detection

Interval B

Green

Red

Main Page

Default Chapter3
- Safety Precautions3
- Table of Contents7
Per Reading this Instruction Manual15
1 ．Outline of the F39516
- What the F395 Can Do16
- Waveform Drawing Procedures17
- Multi-Hold Procedures17
- Hysteresis Procedures18
- Hysteresis 2 Procedures18
- Waveform Comparison19
  - Waveform and Displacement Comparison Procedures19
- Operation Mode at a Glance19
- Standard Interface20
- Waveform Reading20
2 ．Name and Function of each Part21
- Front Pane21
  - Touch Panel Type Color Liquid Crystal Display21
- Rear Panel25
3 ．Screen Configuration and Setting Methods27
- Screen Flow Chart27
- Setting Mode Tree Chart29
- Setting Methods31
  - Specification of Setting Items31
  - Unit Setting Method32
4 ．Methods of Connection34
- Connection to the Cage Clamp Type Terminal Block34
  - Analog Input / Output Connection35
  - SI/F Connection37
- RS-232C Connection38
- Control Connector Connection39
5 ．Methods of Calibration45
- What Is Calibration45
- CH1 Input Calibration and CH2 Input Calibration45
- Equivalent Input Calibration Procedures46
- Actual Load Calibration Procedures47
- LOCK Release48
- Excitation Voltage48
- Unit49
- Increment49
- Decimal Place49
- Zero Calibration49
- Equivalent Input Calibration50
- Actual Load Calibration51
6 ．Settings and Operations Relating to Indicated Values52
- Digital Filter52
- Analog Filter52
- Digital Offset52
- Digital Zero53
7 ．Measurement Operation Functional Settings54
- Operation Mode54
- Sampling Rate54
- Sampling Reset55
- X/Y-Axis Setting by Operation Mode and Input CH55
8 ．Hold Point Display Screen56
9 ．Method of Starting Measurement57
10 ．Multi-Hold Mode61
- Function61
- Setting and Operating Method61
- Hold Functions62
11 ．Hysteresis Mode78
- Function78
- Setting and Operating Method78
- Function79
- Setting and Operating Method79
- Hysteresis 279
13 ．Waveform Comparison / Waveform and Displacement Comparison Mode82
- Function82
- Setting and Operating Method82
- Waveform Sampling Procedures83
- Waveform Comparison Mode87
- Waveform and Displacement Comparison Mode88
- Timing in the Waveform Comparison / Waveform and Displacement Comparison Mode90
- Hold Operation92
  - Operation and Operating Method92
  - Setting Method94
- Un-Passing Area Output94
- Display after Measurement95
14 ．Waveform Editing96
- Waveform Call-Up96
- Waveform Clear96
- Waveform Sampling97
- Waveform Editing98
15 ．Waveform Reading106
- Cursor Center Key108
- Waveform Reading in the Hysteresis / Hysteresis 2 Mode108
- Waveform Reading in the Waveform Comparison / Waveform and Displacement Comparison Mode109
- Hold Jump Function109
- Simple Call-Up of the Waveform Reading Screen110
- Display of Hold Point in the Read Waveform110
- Rejected Waveform Reading110
- Rejected Waveform Clear111
- Y-Axis Start Point111
- Y-Axis Scaling111
- X-Axis Start Point112
- X-Axis Scaling112
- Control Signal Display113
16 ．Code Setting114
- Method of Setting the Operation Ch114
- Each Setting Item117
- Graph Confirmation135
17 ．System-Related Settings and Operations141
- Set Value Protection141
- Display Update Rate141
- Backlight141
- Contrast142
- All Parameters Clear142
- Self-Test142
- Self-Test of ROM & RAM / Self-Test of NOV-RAM145
- Pass Word145
- Switching between Japanese and English145
18 ．Interface146
- SI/F 2-Wire Serial Interface146
- RS-232C Interface147
  - Communication Specifications147
- Interface-Related Settings147
- RS-232C Format149
19 ．Error Messages164
- Details of Messages164
- Method of Checking ADC+OVER / ADC-OVER165
20 ．Block Diagram166
21 ．Outer Dimensions167
22 ．Mounting to a Panel168
23 ．Specifications169
- Analog Input Section169
- Pulse Input Section171
- Display Section171
- Setting Section172
- Input / Output Section172
- External Power Supply (Shared with Excitation Voltage)172
- Interface172
- General Performance173
- Accessories174
24 ．Setting Items List175
25 ．Statement of Conformation to EC Directives177

Unipulse f395 - Slope Detection Interval a; Slope Detection Interval B

Table of Contents