Unipulse f395 - Default Chapter; Safety Precautions

To Next Page

To Previous Page

Safety Precautions

Be sure to read for safety.

In order to have an F395 Dinamic Force Processor used safely, notes I would like you to

surely follow divide into and , and are indicated by the following

documents.Notes indicated here are the serious contents related safely.Please use after

understanding the contents well.

WARNING

CAUTION

WARNING

Misuse may cause the risk of death or serious

injury to persons.

CAUTION

Misuse may cause the risk of injury to persons

or damage to property.

Main Page

Default Chapter3
- Safety Precautions3
- Table of Contents7
Per Reading this Instruction Manual15
1 ．Outline of the F39516
- What the F395 Can Do16
- Waveform Drawing Procedures17
- Multi-Hold Procedures17
- Hysteresis Procedures18
- Hysteresis 2 Procedures18
- Waveform Comparison19
  - Waveform and Displacement Comparison Procedures19
- Operation Mode at a Glance19
- Standard Interface20
- Waveform Reading20
2 ．Name and Function of each Part21
- Front Pane21
  - Touch Panel Type Color Liquid Crystal Display21
- Rear Panel25
3 ．Screen Configuration and Setting Methods27
- Screen Flow Chart27
- Setting Mode Tree Chart29
- Setting Methods31
  - Specification of Setting Items31
  - Unit Setting Method32
4 ．Methods of Connection34
- Connection to the Cage Clamp Type Terminal Block34
  - Analog Input / Output Connection35
  - SI/F Connection37
- RS-232C Connection38
- Control Connector Connection39
5 ．Methods of Calibration45
- What Is Calibration45
- CH1 Input Calibration and CH2 Input Calibration45
- Equivalent Input Calibration Procedures46
- Actual Load Calibration Procedures47
- LOCK Release48
- Excitation Voltage48
- Unit49
- Increment49
- Decimal Place49
- Zero Calibration49
- Equivalent Input Calibration50
- Actual Load Calibration51
6 ．Settings and Operations Relating to Indicated Values52
- Digital Filter52
- Analog Filter52
- Digital Offset52
- Digital Zero53
7 ．Measurement Operation Functional Settings54
- Operation Mode54
- Sampling Rate54
- Sampling Reset55
- X/Y-Axis Setting by Operation Mode and Input CH55
8 ．Hold Point Display Screen56
9 ．Method of Starting Measurement57
10 ．Multi-Hold Mode61
- Function61
- Setting and Operating Method61
- Hold Functions62
11 ．Hysteresis Mode78
- Function78
- Setting and Operating Method78
- Function79
- Setting and Operating Method79
- Hysteresis 279
13 ．Waveform Comparison / Waveform and Displacement Comparison Mode82
- Function82
- Setting and Operating Method82
- Waveform Sampling Procedures83
- Waveform Comparison Mode87
- Waveform and Displacement Comparison Mode88
- Timing in the Waveform Comparison / Waveform and Displacement Comparison Mode90
- Hold Operation92
  - Operation and Operating Method92
  - Setting Method94
- Un-Passing Area Output94
- Display after Measurement95
14 ．Waveform Editing96
- Waveform Call-Up96
- Waveform Clear96
- Waveform Sampling97
- Waveform Editing98
15 ．Waveform Reading106
- Cursor Center Key108
- Waveform Reading in the Hysteresis / Hysteresis 2 Mode108
- Waveform Reading in the Waveform Comparison / Waveform and Displacement Comparison Mode109
- Hold Jump Function109
- Simple Call-Up of the Waveform Reading Screen110
- Display of Hold Point in the Read Waveform110
- Rejected Waveform Reading110
- Rejected Waveform Clear111
- Y-Axis Start Point111
- Y-Axis Scaling111
- X-Axis Start Point112
- X-Axis Scaling112
- Control Signal Display113
16 ．Code Setting114
- Method of Setting the Operation Ch114
- Each Setting Item117
- Graph Confirmation135
17 ．System-Related Settings and Operations141
- Set Value Protection141
- Display Update Rate141
- Backlight141
- Contrast142
- All Parameters Clear142
- Self-Test142
- Self-Test of ROM & RAM / Self-Test of NOV-RAM145
- Pass Word145
- Switching between Japanese and English145
18 ．Interface146
- SI/F 2-Wire Serial Interface146
- RS-232C Interface147
  - Communication Specifications147
- Interface-Related Settings147
- RS-232C Format149
19 ．Error Messages164
- Details of Messages164
- Method of Checking ADC+OVER / ADC-OVER165
20 ．Block Diagram166
21 ．Outer Dimensions167
22 ．Mounting to a Panel168
23 ．Specifications169
- Analog Input Section169
- Pulse Input Section171
- Display Section171
- Setting Section172
- Input / Output Section172
- External Power Supply (Shared with Excitation Voltage)172
- Interface172
- General Performance173
- Accessories174
24 ．Setting Items List175
25 ．Statement of Conformation to EC Directives177

Unipulse f395 - Default Chapter; Safety Precautions

Table of Contents