Unipulse f395 - RS-232 C Format; Writing Set Values

18.Interface
135
18-4. RS-232C Format
18-4-1. Writing Set Values
Ch. No. W 0 1 SP 0 0
Terminator
(0 ~ 32)
Parameter Copy W 0 2 SP 0 0
Terminator
(0 ~ 32)
Select CH W 0 3 SP 0 0
０
Terminator
(0,1)*
Hold Set W 0 4 SP 0 0
Terminator
(0 ~ 20)*
HI Limit W 0 5
±
Terminator
(0000 ~ 9999)
HI-HI Limit W 0 6
±
Terminator
(0000 ~ 9999)
LO Limit W 0 7
±
Terminator
(0000 ~ 9999)
LO-LO Limit W 0 8
±
Terminator
(0000 ~ 9999)
DPM HI W 0 9 SP
Terminator
(0000 ~ 9999)
DPM LO W 1 0 SP
Terminator
(0000 ~ 9999)
Wave Start Level W 1 1
±
Terminator
(0000 ~ 9999)
Wave End Level W 1 2
±
Terminator
(0000 ~ 9999)
Hold Timer W 1 3 SP
Terminator
(0001 ~ 9999)
P&V Difference W 1 4 SP
Terminator
(0001 ~ 9999)
P&V Judg. Rate W 1 5 SP 0 0 0
Terminator
(0 ~ 7)*
P&V Ordinal W 1 6 SP 0 0 0
Terminator
(1 ~ 9)
Minimum Slope W 1 7 SP
Terminator
(0001 ~ 9999)
Interval A W 1 8 SP 0
Terminator
(010 ~ 200)
Interval B W 1 9 SP 0
Terminator
(010 ~ 200)
Pre-Point W 2 0 SP 0 0
Terminator
(00 ~ 10)
Inhibit Timer W 2 1 SP
Terminator
(0000 ~ 9999)
Hys. Interval W 2 2 SP
Terminator
(0000 ~ 9999)
F-T Limit W 2 3 SP
Terminator
(0000 ~ 9999)
F-T Output W24SP000
Terminator
(0,1)*
HH/LL Mode W 2 5 SP 0 0 0
Terminator
(0,1)*
Lv. Axis Select W 2 6 SP 0 0 0
Terminator
(0,1)*
Hold Start Level W 2 7
±
Terminator
(0000 ~ 9999)
Auto Code Up W 2 8 SP 0 0 0
Terminator
(0,1)*
Code Up Point W 2 9 SP
Terminator
(0000 ~ 9999)
HI-LO Relative W 4 0 SP 0 0 0
Terminator
(0,1)*
DPM HI-LO Mode W 4 1 SP 0 0 0
Terminator
(0 ~ 2)*
DPM Hold HI W 4 2 SP
Terminator
(0000 ~ 9999)
DPM Hold LO W 4 3 SP
Terminator
(0000 ~ 9999)
U. Area Output W 4 4 SP 0 0 0
Terminator
(0,1)*
Protect W 8 3 SP 0 0 0
Terminator
(0 ~ 2)*
Display Rate W 8 4 SP 0 0
Terminator
(01 ~ 99)
Backlight W 8 5 SP 0 0
Terminator
(00 ~ 99)