YASKAWA CIMR-JA Series User Manual

Preface.............................................10
Previous Fault ................................109, 217
Programming Mode..........................78, 80, 81
Protective Covers, Removing ...................48, 183
PWM Feedback Data Fault ........................ 124
PWM Feedback Fault ............................. 127
R
RAM Fault ...................................124, 127
Ramp to Stop.......................................91
Rated Output Operation ........................... 102
REMOTE ..........................................84
Replacement Parts ............................159, 195
Restart Enabled................................... 208
Reverse Direction................................. 208
Reverse Operation Selection ....................... 200
Reverse Run Command (2-Wire sequence) ......... 207
RTS Control Selection ............................ 210
Run command ......................................92
Run Command at Power Up ....................... 200
Run Command Input Error ........................ 125
Run Command Input Selection.......................89
Run Command Selection ......................143, 199
Run Command Selection during Program........... 200
Run Command Selection Error.................125, 140
S
S1 .................................................90
S2 .................................................90
Safety Hazard Definitions ...........................12
Safety Information ..................................12
S-Curve Characteristic at Accel End................ 201
S-Curve Characteristic at Accel Start ............... 201
S-Curve Characteristic at Decel End................ 201
S-Curve Characteristic at Decel Start ............... 201
S-Curve Characteristics ........................93, 122
SE ...........................................125, 137
Serial Communication Transmission Error ......125, 134
Setup Mode .................................... 80, 85
Sinking/Sourcing Mode Switch ......................27
Slip Compensation Gain........................... 201
Slip Compensation Primary Delay Time ............ 201
Soft Charge Circuit Fault .......................... 124
Soft CLA Selection ............................... 213
Software No. (Flash) .............................. 217
Software No. (ROM).............................. 217
Software Number (Flash).......................... 109
Software Number (ROM) ......................... 109
Speed Agreement Detection Level ................. 212
Speed Search ..................................... 208
Stall Prevention................................... 122
Stall Prevention Level during Acceleration ......... 211
Stall Prevention Level during Run ................. 212
Stall Prevention Selection during Acceleration ...... 211
Stall Prevention Selection during Deceleration ...... 211
Stall Prevention Selection during Run .............. 211
Standard Connection Diagram ................... 43, 44
STOP Key Function Selection ..................... 214
Stopping Method ...................................91
Stopping Method After Communication Error....... 209
Stopping Method Selection ........................ 200
T
Terminal A1 Bias Setting.......................... 208
Terminal A1 Gain Setting ......................... 208
Terminal A1 Input Voltage ........................ 109
Terminal A1 Signal Level Selection ................ 208
Terminal Block Configuration .......................47
Terminal M1 thru M2 Function Selection (relay) .... 103
Terminal MA, MB and MC Function Selection (relay)
..............................................103, 207
Test Run ......................................... 114
Tightening Torque ..................................50
Timing Fault .................................124, 127
Torque Compensation Gain....................121, 202
Torque Detection 1 (N.O.)......................... 208
Torque Detection 2 (N.O.)......................... 208
Torque Detection Level 1 ......................... 212
Torque Detection Selection 1 ...................... 212
Torque Detection Time 1 .......................... 212
Transistor Input Signal .......................... 61, 62
U
U1-01.............................. 109, 144, 146, 216
U1-02........................................109, 216
U1-03........................................109, 216
U1-06........................................109, 216
U1-07................................... 109, 143, 216
Index
YASKAWA ELECTRIC TOEP C710606 25B YASKAWA AC Drive J1000 Installation & Start-Up Manual
245
2/6/2008-14:44

YASKAWA CIMR-JA Series Specifications

General

Brand	YASKAWA
Model	CIMR-JA Series
Category	Controller
Language	English