5-52
C Multi-function analog input selection (ON: Enable) Yes Yes Yes Yes Yes
D No V/f control with PG (ON: Speed feedback control disabled,) (normal V/f control) No Yes No No No
E Speed control integral reset (ON: Integral control disabled) No Yes No Yes Yes
F Not used (Set when a terminal is not used) - - - - -
10 Up command (Always set with the down command) Yes Yes Yes Yes Yes
11 Down command (Always set with the up command) Yes Yes Yes Yes Yes
12 FJOG command (ON: Forward run at jog frequency d1-17) Yes Yes Yes Yes Yes
13 RJOG command (ON: Reverse run at jog frequency d1-17) Yes Yes Yes Yes Yes
14 Fault reset (Reset when turned ON) Yes Yes Yes Yes Yes
15
Emergency stop. (Normally open condition: Deceleration to stop in deceleration
time set in C1-09 when ON.)
Yes Ye s Yes Yes Yes
16 Motor switch command (Motor 2 selection) Yes Yes Yes Yes Yes
17
Emergency stop (Normally closed condition: Deceleration to stop in deceleration
time set in C1-09 when OFF)
Yes Ye s Yes Yes Yes
18
Timer function input (Functions are set in b4-01 and b4-02 and the timer function
outputs are set in H1- and H2-.)
Yes Ye s Yes Yes Yes
19 PID control disable (ON: PID control disabled) Yes Yes Yes Yes Yes
1A Accel/Decel time 2 Yes Yes Yes Yes Yes
1B
Parameters write enable (ON: All parameters can be written-in. OFF: All
parameters other than frequency monitor are write protected.)
Yes Ye s Yes Yes Yes
1C Trim control increase (ON: d4-02 frequency is added to analog frequency reference.) Yes Yes Yes Yes Yes
1D
Trim control decrease (ON: d4-02 frequency is subtracted from analog frequency
reference.)
Yes Ye s Yes Yes Yes
1E Analog frequency reference sample/hold Yes Yes Yes Yes Yes
20 to
2F
External fault (Desired settings possible)
Input mode: NO contact/NC contact, Detection mode: Normal/during operation
Yes Ye s Yes Yes Yes
30
PID control integral reset (reset when reset command is input or when stopped
during PID control)
Yes Ye s Yes Yes Yes
31 PID control integral hold (ON: Hold) Yes Yes Yes Yes Yes
32 Multi-step speed reference 4 Yes Yes Yes Yes Yes
34 PID soft starter Yes Yes Yes Yes Yes
35 PID input characteristics switch Yes Yes Yes Yes Yes
60 DC injection braking command (ON: Performs DC injection braking) Yes Yes Yes Yes Yes
61 External search command 1 (ON: Speed search from maximum output frequency) Yes No Yes No Yes
62 External search command 2 (ON: Speed search from set frequency) Yes No Yes No Yes
63 Field weakening command (ON: Field weakening control set for d6-01 and d6-02) Yes Yes No No No
64 External speed search command 3 Yes Yes Yes Yes Yes
65 KEB (deceleration at momentary power loss) command (NO contact) Yes Yes Yes Yes Yes
66 KEB (deceleration at momentary power loss) command (NO contact) Yes Yes Yes Yes Yes
67
Communications test mode (“Pass” is displayed when the communications test is
passed.)
Yes Ye s Yes Yes Yes
68 High-slip braking (HSB) Yes Yes No No No
69
Jog 2
Closed = Drive runs at frequency reference entered into parameter d1-17.
Direction is determined by FWD/REV input. Three-wire control only
No Yes Yes Yes Ye s
6A
Drive Enable
Closed = Drive will accept run command.
Open = Drive will not run. If running , drive will stop per b1-03.
Yes Ye s Yes Yes Yes
Setting
Value
Function
Control Methods
V/f
V/f
with
PG
Open
Loop
Vector
1
Flux
Vector
Open
Loop
Vector
2
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
To Next Page
Loading...
