YOKOGAWA PT500 User Manual

132 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #2 background image

Loading...

Page #2 background image

Table of Contents

Default Chapter3
- Table of Contents3
Chapter1 Normal/Maintenance Mode5
- Selection of the Maintenance Mode7
Chapter 2 I/F Set-Up (MAINTENANCE 1)7
- Hardware Setting9
- I/F Set-Up9
- Select the I/F Set-Up Data9
- Setting of the Gyrocompass11
- Setting of the INS/GPS Input Format12
- ２． Hardware Setting13
- ２．１ Hardware Setting of the Gyrocompass14
- ２．３ Hardware Setting of the INS/GPS20
  - Hardware Setting of the LOG21
  - ３． Software Setting22
- ３．１ Software Setting of the Gyrocompass Input23
- ３．３ Software Setting of the INS/GPS Input32
- ３．４ Software Setting of the INS/GPS Output41
Chapter 3 Memory Access-FIX (1 Bite) (MAINTENANCE 2)49
- Memory Access - FLX51
Chapter 4 Memory Access-FLT(4 Bite) (MAINTENANCE 3)51
Chapter 5 DAC Output (MAINTENANCE 4)53
Chapter 6 Actual Rudder Angle Output (MAINTENANCE 5)55
Chapter 7 Course Deviation Output (MAINTENANCE 6)57
Chapter 8 Display of the Analogue Input (MAINTENANCE 7)59
Chapter 9 Program Version Number (MAINTENANCE 8)61
Chapter 10 Program Cold Start (MAINTENANCE 9)63
- Select the Ship’s Parameter65
Chapter 11 Input and Calculate the Ship's Parameter (PT500A)(MAINTENANCE 10) １１－１65
- Kind of Ship66
- Input the Length between Perpendiculars67
- Input the Block Coefficient (Cb)69
- Input the Area Pf Rudder (Ar)69
- Input the Navigation Speed70
- Ship’s Maneuverability70
- Display of the Ship’s Maneuverability71
- Display of Result of Identification73
- Off Course Alarm SW75
Chapter 12 Display the Result of Identification（Pt500A）(MAINTENANCE 11) ·· １２－１75
Chapter 13 Off Course Alarm ＳＷ(MAINTENANCE 12)75
- Bar-Graph SW77
Chapter 14 Bar Graph ＳＷ (MAINTENANCE 13)77
Chapter 15 Beep of the Key Operation ＳＷ (MAINTENANCE 14)79
Chapter 16 Select the Course after Auto Override Steering (MAINTENACE 15)81
- Display Analog Voltage Value83
Chapter 17 Display Analogue Voltage Value (MAINTENANCE 16) ················· １７－１85
Chapter 18 Option Setting Mode (MAINTENANCE 17)85
- Option Setting87
Chapter 19 Alarm Threshold of Servo Loop Failure87
Chapter 20 Gyrocompass Moving Average Time of CMZ300X Format93
Chapter 21 Analog Recorder Output for Wide Rudder Angle Mode95
- Relation of the Analog Voltage and Wide Angle Value96
- Speed Gain Compensation97
- Lower Limit of High Speed Area100
- Upper Limit of Low Speed Area100
- High Gain Multiplier101
- Low Gain Multiplier101
Chapter 22 Speed Gain Compensation (PT500D・SUB AUTO) ····················· ２２－１103
Chapter 23 Select the Heading Monitor Function103
Chapter 24 Alarm Threshold of Rudder Erroneous105
- Set the Detection Time106
Chapter 25 Alarm Threshold of Heading Erroneous107
Chapter 26 Boundary of Speed Status Output109
- Select Enable or Disable of the Speed Status Output110
Chapter 27 Special Flag Setting (MAINTENANCE 18)111
- Option Flag-0 Setting113
- Rate down Check Setting119
- Pilot Operation Mode120
- Option(Special) Data-0 Setting121
- Option(Special) Data-1 Setting123
- Option(Special) Data-2 Setting124
- Option(Special) Data-3 Setting125
- Option(Special) Data-4 Setting126
- Option(Special) Data-5 Setting128
Chapter 28 Notice131

Questions and Answers:

Need help?

Do you have a question about the YOKOGAWA PT500 and is the answer not in the manual?

YOKOGAWA PT500 Specifications

General

Brand	YOKOGAWA
Model	PT500
Category	Autopilot System
Language	English