ZF Marine ClearCommand User Manual

DIP SWITCH SET-UP PROCEDURES
Page 32
Change Throttle Pause by setting the Dip Switches on the Processor
Main Circuit Boards using the following steps.
6.7
ENGINE SIGNAL SELECTION
The Engine Signal selection is preset at the Factory for Scania
Engines.
Set the SW1 Dip Switches on the Processor Main Circuit Board for the
engine signal required for this application by following steps below.
A)Place the System in Set-up Mode by following Section 6.1.5,
page 26.
B) Place the appropriate SW1 Dip Switches On for the engine sig-
nal required for this application.
•Refer to Figure 23:, page 32, for the Dip Switch settings..
A)Place the System in Set-up Mode by follow-
ing Section 6.1.5, page 26.
B)Place the appropriate Dip Switches ON for
Throttle Pause required for this application.
• Refer to Figure 22:, page 32, for the Dip
Switch settings.
C)Store the value that has been set by follow-
ing Section 6.1.6, page 27.
Figure 22: Dip Switch Setting Throttle Pause
CAUTION: The setting on all Processors Main Circuit Boards MUST be set the same for Twin
Screw (or more) applications.
CAUTION: Ensure that the Jumper 6 setting on the Processor Auxiliary Board is the correct set-
ting for the Engine Signal Selection required for this vessel. Refer to the Drawing in
Appendix C.1 for Jumper 6 location.
Figure 23: Dip Switch Setting Engine Signal Selection
To c hange, u s e a
small screwdriver.
0657-600
1234
5
67
OFF
PUSH DOWN
FOR ‘ON’
PUSH DOWN
FOR ‘OFF’
OFF
OFF
OFF
OFF
OFF
OFF
ON
0.5 Second
FACTORY DEFAULT
0657-600
1
234
5
67
OFF
PUSH DOWN
FOR ‘ON’
PUSH DOWN
FOR ‘OFF’
OFF
OFF
OFF
OFF
OFF
ON
1.0 Second Pause
ON
0657-600
1
2
3
4
5
6
7
OFF
PUSH DOWN
FOR ‘ ON’
PUSH DOWN
FOR ‘ OFF’
OFF
OFF
OFF
OFF
ON
ON
ON
Cummins
Quantum
(voltage) (1.2-4.0V)
0657-600
1
2
3
4
5
6
7
OFF
PUSH DOWN
FOR ‘ ON’
PUSH DOWN
FOR ‘ OFF’
OFF
OFF
OFF
ON
ON
ON
ON
Voltage Engines
(voltage)(.5-4.5V)
Caterpillar
(PWM)
0657-600
1
2
3
4
5
6
7
OFF
To change, use a small screwdriver.
PUSH DOWN
FOR ‘ ON’
PUSH DOWN
FOR ‘ OFF’
OFF
OFF
OFF
OFF
ON
ON
OFF
Cummins
Centry
(voltage)(.9-4.5V)
0657-600
1
2
3
4
5
6
7
OFF
PUSH DOWN
FOR ‘ ON’
PUSH DOWN
FOR ‘ OFF’
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
0657-600
1
2
3
4
5
6
7
OFF
PUSH DOWN
FOR ‘ ON’
PUSH DOWN
FOR ‘ OFF’
OFF
OFF
OFF
ON
ON
MTU
(current)(4-20mA)
Scania
(volta
g
e)(.3-2.9V)
FACTORY DEFAULT
OFF
0657-600
1
2
3
4
5
6
7
OFF
PUSH DOWN
FOR ‘ ON’
PUSH DOWN
FOR ‘ OFF’
OFF
OFF
ON
ON
ON
OFF

ZF Marine ClearCommand Specifications

General

Brand	ZF Marine
Model	ClearCommand
Category	Controller
Language	English