ABB ACS800 Series - Page 197

Additional data: actual signals and parameters
185
65.15 SENSOR MIN DIA 1.0 inch 1.0 inch 1.0 inch 1.0 inch 1.0 inch 1299
65.16 DIA > LIM1 30.0 inch 30.0 inch 30.0 inch 30.0 inch 30.0 inch 1300
65.17 DIA > LIM2 35.0 inch 35.0 inch 35.0 inch 35.0 inch 35.0 inch 1301
65.18 DIA < LIM1 10.0 inch 10.0 inch 10.0 inch 10.0 inch 10.0 inch 1302
65.19 DIA < LIM2 5.0 inch 5.0 inch 5.0 inch 5.0 inch 5.0 inch -
65.20 RESET WHILE RUN NO NO NO NO NO -
65.21 EXT DIA SEL AI6 AI6 AI6 AI6 AI6 -
65.22 DIA HOLS PTR +.000.000.00 +.000.000.00 +.000.000.00 +.000.000.00 +.000.000.00 -
66 TORQUE MEM CTRL
66.01 TORQUE MEM SAMPLE (not visible) (not visible) NOT SEL NOT SEL NOT SEL 1303
66.02 TORQUE MEM ENABLE (not visible) (not visible) NOT SEL NOT SEL NOT SEL 1304
66.03 TORQUE BOOST SEL (not visible) (not visible) ON DELAY ON DELAY ON DELAY 1305
66.04 BOOST ON DELAY (not visible) (not visible) 5.0 s 5.0 s 5.0 s 1306
66.05 TORQUE BOOST % (not visible) (not visible) 100% 100% 100% 1307
66.06 MTR TQ FILT TIME (not visible) (not visible) +.000.000.00 +.000.000.00 +.000.000.00 1308
66.07 TORQ MEM SMPL PTR (not visible) (not visible) +.000.000.00 +.000.000.00 +.000.000.00 1309
66.08 TORQ MEM ENBL PTR (not visible) (not visible) +.000.000.00 +.000.000.00 +.000.000.00 1310
67 LEAD CTRL
67.01 WEB SPD INPUT (not visible) (not visible) (not visible) (not visible) AI1 1321
67.02 WEB SPD SCALE (not visible) (not visible) (not visible) (not visible) 1660.0 1322
70 DDCS CONTROL
70.01 CH0 NODE ADDR 1 1 1 1 1 1375
70.02 CH0 BAUD RATE 1 Mbit/s 1 Mbit/s 1 Mbit/s 1 Mbit/s 1 Mbit/s 1376
70.05 CH2 NODE ADDR 1 1 1 1 1 1379
70.06 CH2 M/F MODE NOT IN USE NOT IN USE NOT IN USE NOT IN USE NOT IN USE 1380
70.07 MASTER SIGNAL 1 225 225 225 225 225 1381
70.08 MASTER SIGNAL 2 202 202 202 202 202 1382
70.09 MASTER SIGNAL 3 213 213 213 213 213 1383
70.10 M/F COMM DELAY 0 ms 0 ms 0 ms 0 ms 0 ms 1384
70.11 M/F COM LOSS CTRL NO ERR CHK NO ERR CHK NO ERR CHK NO ERR CHK NO ERR CHK 1385
70.12 CHANNEL 3 ADDR 1 1 1 1 1 1386
70.13 NUM OF TQ FOLLWR
83 ADAPT PROG CTRL
83.01 ADAPT PROG CMD EDIT EDIT EDIT EDIT EDIT 1609
83.02 EDIT COMMAND NO NO NO NO NO 1610
83.03 EDIT BLOCK 0 0 0 0 0 1611
83.04 TIMELEVEL SEL 100 ms 100 ms 100 ms 100 ms 100 ms 1612
83.05 PASSCODE 000001613
84 ADAPTIVE PROGRAM
84.01 STATUS 1628
84.02 FAULTED PAR 1629
84.05 BLOCK1 NO NO NO NO NO 1630
84.06 INPUT1 0 0 0 0 0 1631
84.07 INPUT2 0 0 0 0 0 1632
84.08 INPUT3 0 0 0 0 0 1633
84.09 OUTPUT 0 0 0 0 0 1634
…… …
1644
84.79 OUTPUT 0 0 0 0 0 -
85 USER CONSTANTS
85.01 CONSTANT1 0 0 0 0 0 1645
85.02 CONSTANT2 0 0 0 0 0 1646
85.03 CONSTANT3 0 0 0 0 0 1647
85.04 CONSTANT4 0 0 0 0 0 1648
85.05 CONSTANT5 0 0 0 0 0 1649
85.06 CONSTANT6 0 0 0 0 0 1650
Index Name/Selection UNWIND
TENSION
UNWIND
DANCER
WINDER
TENSION
WINDER
DANCER
WINDER
LEAD
PB