Diagnostic Test Descriptions
Control Software Version # Test d 1
This option displays the control software version number. To start
test, control must be in the Testing Mode. Refer to How to Enter
Diagnostic Testing Feature at the beginning of this section.
To enter, press the START (enter) keypad. The display will show
S XXX where XXX is the software version number.
To exit the test, press the Warm (<) keypad. The control will re-
turn to the Testing Mode.
Input/Output Board Software Version Test d 2
This option displays the input/output board software version
number. To start test, control must be in the Testing Mode. Refer
to How to Enter Diagnostic Testing Feature at the beginning of
this section.
To enter, press the START (enter) keypad. The display will show
ob XX where XX is the software version number.
To exit the test, press the Warm (<) keypad. The control will re-
turn to the Testing Mode.
Drive Board Software Version Test d 3
This option displays the drive board software version number. To
start test, control must be in the Testing Mode. Refer to How to
Enter Diagnostic Testing Feature at the beginning of this section.
To enter, press the START (enter) keypad. If the door is open the
display will show CLoSE, door until the door is closed. Once
the door is closed he Display will show db vEr and flash the
START (enter) keypad LED. To start the test, press the START
(enter) keypad. If the door is unlocked when the test is started,
the control will attempt to lock the door. The display will show a
sequence of horizontal LED segments to indicate it is waiting for
the door to lock or drive version. Once the door is locked the dis-
play will show db XX where XX is the software version of the
drive.
To exit the test, press the Warm (<) keypad. The control will re-
turn to the Testing Mode.
If the door was unlocked when the test began, the control will at-
tempt to unlock the door.
Drive Parameter Version Test d 4
This option displays the drive parameter version number. To start
test, control must be in the Testing Mode. Refer to How to Enter
Diagnostic Testing Feature at the beginning of this section.
To enter, press the START (enter) keypad. If the door is open the
display will show PArXXX where XXX is the drive parameter
version number.
To exit the test, press the Warm (<) keypad. The control will re-
turn to the Testing Mode.
Service Door Opening Test d 8
This option tests the service door switch. To start test, control
must be in the Testing Mode. Refer to How to Enter Diagnostic
Testing Feature at the beginning of this section.
To enter, press the START (enter) keypad. The display will show
S oP when the service door switch is open and S CL when the
service door switch is closed.
The service door switch has to be closed for at least one second
and opened for at least one second for the display to change. This
test will add a count to the service door opening counter for the
audit and save the date/time for each opening.
Coin Vault Opening Test d 9
This option tests the coin vault switch. To start test, the control
must be in the Testing Mode. Refer to How to Enter Testing Fea-
ture at the beginning of this section.
To enter, press the START (enter) keypad. The display will show
v oP when the coin vault switch is open and v CL when the
coin vault switch is closed.
The coin vault switch has to be closed for at least one second and
opened for at least one second for the display to change. This test
will add a count to the coin vault opening counter for the audit
and save the time/date for each opening.
To exit the Coin Vault Opening Test, press the Warm (<) keypad.
The control will return to the Testing Mode.
Coin Drop #1 Input Test d 10
This option tests coin drop #1. To start test, control must be in the
Testing Mode. Refer to How to Enter Diagnostic Testing Feature
at the beginning of this section.
To enter, press the START (enter) keypad. The display will show
C1 XX. The XX will show the number of coins entered and will
increment one for each coin entered in coin drop #1.
NOTE: Coins entered in test mode will not increment
the total # of coins counter that is accessed in the audit
feature.
Coin Drop #2 Input Test d 11
This option tests coin drop #2. To start test, control must be in the
Testing Mode. Refer to How to Enter Diagnostic Testing Feature
at the beginning of this section.
To enter, press the START (enter) keypad. The display will show
C2 XX. The XX will show the number of coins entered and will
increment one for each coin entered in coin drop #2.
NOTE: Coins entered in test mode will not increment
the total # of coins counter that is accessed in the audit
feature.
Machine Diagnostic Functions
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
124 Part No. F8615401ENR4
To Next Page
Loading...
