Machine Operation
Power Up
When power is applied to the machine, the control becomes ac-
tive and will display its software version as SXXX (XXX is the
version number) for one (1) second.
System Check Mode
This mode is entered after Power Up unless the next mode to be
entered after System Check Mode is Run Mode . The next mode
is determined in Power Up . The purpose of this mode is for the
FEC to verify that the correct I/O Board is connected. Once all
required conditions are confirmed, the control will automatically
exit System Check Mode and proceed to the next mode. In addi-
tion to checking the I/O Board System Check Mode, the control
will initialize a drive power up check if the door is closed. After
System Check Mode is exited, the control may lock the door and
power up the drive to verify that the correct drive is installed. If
the door is opened at any time, the drive power up check is can-
celed until the next time the door is locked. The display will
show the software version number similar to Power Up .
Ready Mode
In this mode of operation the control indicates the current select-
ed cycle and current selected modifiers by lighting the LEDs. The
full current vend price for the cycle appears in the display. The
Insert Coins/Card LED is lit.
The user will be able to select a different cycle by pressing a cy-
cle keypad or cycle modifier by pressing a cycle modifier keypad
when the machine is in Ready Mode.
Partial Vend Mode
The control enters this mode when part of the vend price has been
entered, but not enough vend is entered to satisfy the vend price.
The remaining vend price needed to start the cycle appears in the
display. The Insert Coins/Card LED is lit.
The user will be able to select a different cycle and/or modifier
by pressing a cycle keypad when the machine is in Partial Vend
Mode.
Additional Vend Mode
The control enters this mode if a higher priced cycle or a cycle
modifier is selected while the machine is in Start Mode or Run
Mode, but before the first Fill Step has completed. If the vend
price is not satisfied within one (1) minute, the control will go
back to the first selection and the cycle will continue if it was
paused. After the first Fill Step, all key presses will be ignored al-
lowing the machine to go through the complete cycle.
Start Mode
The control enters this mode when the full vend price is satisfied,
the vend price is zero (0) or the control is in OPL Mode. START
(enter) keypad LED will flash one (1) second on and one (1) sec-
ond off. If Start Mode is entered because the vend price is satis-
fied or the control is in OPL Mode, the display will show PUSH
for one (1) second, Strt for one (1) second and the current cycle
time for one (1) second. If Start Mode is entered because the
vend price is zero (0), the display will show FrEE. When first
entering Start Mode, a signal will sound for one (1) second on
and one (1) second off for 10 seconds if Signal for Start is ena-
bled.
After pressing the START (enter) keypad if the door is closed,
Door Locking Mode will be entered and the cycle will begin.
If the door is not closed when the vend price is satisfied, CLoSE
and door will be displayed until the door is closed. Once door is
closed, the START (enter) keypad must be pressed to lock door
and start the cycle.
Door Locking Mode
The control enters this mode after the START (enter) keypad is
pressed in Start Mode or Pause Mode to start or resume a ma-
chine cycle. The control will stay in Door Locking Mode until the
loading door is closed and locked. The display shows a single
moving LED and the Door Lock LED flashes one (1) second on/
off.
Once the door is locked, the control will exit Door Locking Mode
and will enter Run Mode. If the door is opened prior to being
locked, the control will return to Start Mode.
An error will be displayed if the door fails to lock after the third
attempt. The machine will attempt to lock for one (1) additional
minute. If the door fails to lock, the control will return to Start
Mode.
If the door locks, the door lock error will clear and the cycle will
continue normally. The door can be opened to clear the door lock
error as well.
Machine Operation
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22 Part No. F8615401ENR4
To Next Page
Loading...
