Vend Price #1 AtS 1
This option allows the owner to set the vend price for all cycles,
but otherwise specifically for Normal Hot . This price should be
set before all other prices. This vend price will be shown in the
display when Normal Hot is selected.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad.
3.
AtS 1 will appear in the display. Press the START (enter)
keypad. All cycle LEDs will be lit to show all cycle prices are
being programmed.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price #2 AtS 2
This option allows the owner to set the vend price for Normal
Warm. This vend price will be shown in the display when Normal
Warm is selected.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad.
3.
AtS 1 will appear in the display. The keypad LED will be lit
to show which cycle price is being programmed.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options. When AtS 2 appears in
the display, press the START (enter) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price #3 AtS 3
This option allows the owner to set the vend price for Normal
Cold. This vend price will be shown in the display when Normal
Cold is selected.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad.
3.
AtS 1 will appear in the display. The keypad LED will be lit
to show which cycle price is being programmed.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options. When AtS 3 appears in
the display, press the START (enter) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price #4 AtS 4
This option allows the owner to set the vend price for a Perma-
nent Press Hot. This vend price will be shown in the display
when Permanent Press Hot is selected.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad.
3.
AtS 1 will appear in the display. The keypad LED will be lit
to show which cycle price is being programmed.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options. When AtS 4 appears in
the display, press the START (enter) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
46 Part No. F8615401ENR4
To Next Page
Loading...
