Cycle Modifier Ultra Additional Rinse Time CNP 7
This option allows the owner to add additional time to agitate
steps that have Rinse 1 selected as their status. The additional
rinse time option needs to be turned on for the Cycle Modifier
Additional Rinse Time to take effect.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until CNP 7 appears in the
display.
6.
When CNP 7 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Rinse 1
selected as their status.
7. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the current number of minutes.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Enter Cycle Programming
CyCLE-
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until CyCLE- appears in
the display. Press the START (enter) keypad and CyCLE1
will appear in the display.
NOTE: The LED light next to the select cycle keypad
will be lit to indicate which cycle is being program-
med.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the cycles to program.
5. Press the START (enter) keypad when the desired cycle ap-
pears in the display. PCyCtd will appear in the display if ena-
bled. Otherwise the first cycle step will appear. Refer to Table
13 for keypad navigation.
6. For each cycle, the Programmable Cycle Time Display can be
programmed, if enabled in Global Programming Parameters
(refer to Programmable Cycle Time Display PCyCtd). Press
the START (enter) keypad to program the displayed time.
7. Press the Delicates Bulky (∧) or the Cold (∨) keypad until the
desired value is on the display. Values range from 0-65535. A
value of 0 will disable Programmable Cycle Time for the se-
lected cycle. This allows for some cycles to use a Programma-
ble Cycle Time while others use the time calculated from the
enabled steps.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
8. Press the START (enter) keypad. The new value is saved and
01XXXX appears in the display. The first two digits represent
the Cycle Step number and will flash. XXXX will show the
step type. The machine is able to have up to 50 custom steps
programmed for each cycle. Within each step there are several
programmable options. Refer to the following sections for de-
tails about each step type and its options.
9.
After the last cycle step is stored, CyCEnd is displayed. If 50
steps are programmed CyCEnd will not be displayed. To in-
sert a step at the end of the cycle, first go to this display and
then press the Regular key pad.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
83 Part No. F8615401ENR4
To Next Page
Loading...
