Lockout Mode
If enabled in the Control Configuration via the network or IR de-
vice, the control enters Lockout Mode to prevent the machine
from being used except by a particular user who has reserved the
machine in advance.
This mode is entered when the current time (in hours and mi-
nutes) falls within the time period set by the Lockout Mode Start
Time Hour, Lockout Mode Start Time Minute, Lockout Duration,
and when the control is in Ready Mode. The display shows rES.
User access is ignored until the control exits Lockout Mode. The
control will be able to communicate with the network, IR device,
or the serial payment system. If the Lockout Duration is program-
med to zero (0), the control will immediately exit Lockout Mode.
Exiting Lockout Mode requires a four (4) keypad sequence (de-
faulted as Regular, Deluxe, Ultra and Normal) followed by the
START (enter) keypad. The corresponding LED lights as each
keypad is pressed. If an incorrect sequence is entered, the se-
quence resets, all LED’s turn off, and keypresses are ignored for
five (5) seconds.
When the correct sequence is entered, the control enters Ready
Mode.
Shutdown Mode
If the Low Power/Auto-Shutdown Option is enabled (refer to Pro-
gramming Control) the control enters Shutdown Mode at a pro-
grammed time, day-of-week, date, month, and year.
The control must be in Ready Mode, Drop-Off Mode, Lockout
Mode, or Start Mode when no vend has been entered to enter
Shutdown Mode. While in Shutdown Mode, the display shows
oFF and all LEDs will be turned off.
The control automatically exits Shutdown Mode at a programmed
time, day-of-week, date, month, and year. Shutdown Mode can be
exited by disabling the Low Power/Auto-Shutdown Option man-
ually or through network or IrDA commands.
OPL Mode
This feature allows the user to start a cycle without satisfying the
vend price.
When in OPL Mode, press and hold the Normal and Permanent
Press keypads to terminate the cycle and enter Door Unlocking
Mode and then End of Cycle Mode.
For details on enabling OPL Mode, refer to OPL Parameters
oPL-.
Drop-Off Mode
This feature allows the owner to limit machine use to an attend-
ant without requiring vend.
Starting the machine requires a four (4) keypad sequence (de-
faulted as Regular, Deluxe, Ultra and Normal) followed by the
START (enter) keypad. To cancel Drop-Off Mode, press Normal
and Permanent Press.
These keypad sequences can be reprogrammed by an external de-
vice.
For details on enabling Drop-Off Mode, refer to Drop Off Mode
droP.
Out of Order Mode
This feature allows the owner to program Out of Order Mode
which can be used to show the owner that the machine is not
available to use. The control will accept coins and increment the
appropriate audit counters but the vend entered will not count to-
wards a cycle purchase, the coin audio will not work, and no cy-
cle will run while Out of Order Mode is active.
Refer to Out of Order oUt.
Network Node Number Display Mode
This feature allows the owner to program a command via IrDA or
network that requests the control to display the network node
number. The control will displays nXXX where XXX is the net-
work node number.
While in this mode, press the Permanent Press and Delicates Bul-
ky keypads to enter Network Node Number nodE .
Error Display Mode
In Error Display Mode, the display shows machine errors when
they occur. The display only shows one error at the time if there
are multiple errors. Once the highest priority error is cleared, the
next highest priority error will be displayed.
Refer to Error Codes for more on error details, displays, and pri-
orities.
Communications Mode
This feature allows the control to communicate with an IrDA,
card reader or network. This allows the owner to program the
control and read control data without using the keypad.
For more detailed information on using the Communications
Mode feature, refer to Communications.
Machine Operation
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
25 Part No. F8615401ENR4
To Next Page
