Cool Down Water Temperature (Heat
Models) CooLdn
This option allows the owner to set the cool down global water
temperature for cool down steps.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
CooLdn appears in the display.
4. Press the START (enter) keypad. A number will appear in the
display. This number corresponds to the current Water Tem-
perature setting and is displayed in Fahrenheit or Celsius
based on the temperature setting.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the current water temperature value to the
desired water temperature value.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Low Water Level FL Lo
This option allows the owner to set the low water level which can
be used in fill steps to set water levels in cycle programming.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until FL Lo appears in the
display.
4.
When FL Lo appears in the display, press the START (enter)
keypad. A number will appear in the display. This number
corresponds to the current Water Level setting.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to
change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Medium Water Level FL NEd
This option allows the owner to set the medium water level
which can be used in fill steps to set water levels in cycle pro-
gramming.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until FL NEd appears in
the display.
4.
When FL NEd appears in the display, press the START (en-
ter) keypad. A number will appear in the display. This number
corresponds to the current Water Level setting.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to
change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
High Water Level FL Hi
This option allows the owner to set the high water level which
can be used in fill steps to set water levels in cycle programming.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until FL Hi appears in the
display.
4.
When FL Hi appears in the display, press the START (enter)
keypad. A number will appear in the display. This number
corresponds to the current Water Level setting.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to
change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
60 Part No. F8615401ENR4
To Next Page
