Cycle Modifyer Deluxe Vend Price Add-
er ACNP 1
This option allows the owner to set the vend price for the Deluxe
modifier key. This price is added onto the cycle price.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until ACNP 1 appears in
the display. The Deluxe modifier LED will be lit to show
which price is being programmed.
4.
When ACNP 1 appears in the display, press the START (en-
ter) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifyer Ultra Vend Price Adder
ACNP 2
This option allows the owner to set the vend price for the Ultra
modifier key. This price is added onto the cycle price.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until ACNP 2 appears in
the display. The Ultra modifier LED will be lit to show which
price is being programmed.
4.
When ACNP 2 appears in the display, press the START (en-
ter) keypad.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price Decimal Point Ats dP
This option allows the owner to enable a decimal point to show
up in the vend price at one of two locations. For example, a vend
price of 200 can be display with a decimal point as 2.00 or
0.200.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until Ats dP appears in
the display. Press the START (enter) keypad.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the parameter.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
49 Part No. F8615401ENR4
To Next Page
Loading...
